Bose VIRTUALLY INVISIBLE 191 - Manual (Page 12)

12
 
S TEPS TO I NSTALLING
English Français Nederlands Deutsch Italiano
Figure 12
Checking the space for the
width of the speaker
360°
• If the wire goes around the 360° arc without a problem, proceed to step 5 below.
• If you cannot rotate the wire all the way around up to the first bend, you need to drill a
new pilot hole elsewhere. Then repeat the preceding steps 3 and 4.
5. Use the bent wire to check for enough length below the hole:

Holding the short end of the wire, insert the long end into the wall or ceiling and straight
down from the hole (Figure 13a).
7LS You may want to use the template for this step, as shown in Figure 13b.
• With the long end of the wire still in the hole, sweep it from side to side in a curve as
shown on the template. This indicates if the wall or ceiling space is long enough and
wide enough at the far end.
7LS When testing for length, move the wire near the wall or ceiling, then farther back from it
(as in Figure 13a, below).
Figure 13
Inserting the long end of the
wire (a) and sweeping from
side to side to check the
length (b)
(a)
5 1 / 2 " (14 cm)
8 1 / 16 " (20.5 cm)
14 1 / 2 " (36 .9 cm )
TAPE HER E
TAPE HER E
TAPE HER E
WHITE CUT OUT AREA
WHITE CUT OUT AREA
Pilot
Hole
WAR NING : Mak e sure the sp ot cho sen is safe for cu tting. Do no t cut th rough
surfac es tha t ha ve ha zards, such as ele ctrica l wirin g, con duits or plu mbin g,
conce aled beh ind th em. If you a re no t sure , cons ult a profe ssion al ins talle r
befo re yo u pro ceed.
DO NOT CUT ARO UND GRAY AREA Eng lish & Tra nsla tions
WAR NING : Mak e sure the spo t chose n is s afe fo r cutting . Do not cu t thro ugh s urfaces that hav e haz ards, such as ele ctrica l
wiring, cond uits o r plum bing, conce aled b ehind them . If y ou are n ot sur e, con sult a profe ssion al ins taller befo re you proc eed.
WARN ING: Make sure the s pot ch osen is safe for
drilling . Don ot cut throug h surfac es tha t have hazard s
conce aled behin d them, such as elec trical wiring ,
condu its or plum bing. If you are not sure , cons ult a
profe ssiona l inst aller b efor e you proce ed. WARN ING: M ake s ure the spot chosen is safe for
drilling. Do no t cutth rough surfac es tha t have hazard s
concea led be hind them , such as ele ctrical wiring ,
cond uits o r plum bing. If you a re no t sur e, con sult a
profe ssion al ins taller before you proc eed.
WA RNIN G:Ma ke sure the spot c hosen is safe for drilling . Do n otcut th rough surfac es th at hav e haza rds conce aledb ehind them , such asele ctrical wiring , cond uitsor plumb ing. If you areno t sure, consul t a profes sional installe r befo re youpro ceed. WAR NING: Make sure t he s potcho sen is safe f or drilli ng.D o not cu t throug h surfac es tha t have hazar ds con cealed beh ind th em, s uch as ele ctrical wiring , condu its or plumbi ng. If you are not su re, co nsult a profes siona l insta ller befor e you proce ed.
WAR NING : Make surethe spotc hosen is saf e
fordrill ing. D onotc utthro ughsu rfaces thatha ve
hazard s con cealed behin d them , such as
electric al wirin g, con duits or plu mbing . If yo u
areno t sure, cons ult a profess ional installe r
befor e you proce ed.
WAR NING : Make s ure th e spo t
chos en is safe for dril ling.D o not c ut
throug h su rfaces that have hazar ds
conce aled behin d them , such as
electric alwirin g, co nduits orplu mbing .
If you are not su re, co nsult a
profe ssiona l insta ller be fore y ou
proce ed.
9" (22 .9 cm )
TAPE HERE
Transl ations below
TAPE HER E
TAPE HERE
DO NOT CUT ARO UND GRAY AREA
DO NOT CUT ARO UND GRAY ARE A
DO NOT CUT AROU ND GRAY AREA
DO N OT CUT ARO UND GR AY A REA
DO NOT CUT A ROU ND GRAY AREA
DO NO
T CUT ARO UND GRAY AR EA
DO NOT CUT ARO UND GRAY AREA
(b)
• If the wire goes in and sweeps from side to side at the far end without a problem, proceed
to the next major step: “Prepare the wall for inserting the speaker” on page 13.
• If you find an impediment below the pilot hole, and you are working in an interior wall,

insert the wire upward. If there are no impediments above the pilot hole, you can install the
speaker upside-down. If you are working in an exterior wall, installing the speaker

upside-down is not recommended. In this case, if you find an impediment you need to drill
a new pilot hole elsewhere. Then repeat the preceding steps 3, 4, and 5.