Sound Devices 744T - Manual (Page 74)

744T User Guide and Technical Information
68
v. 2.67 Features and specifications are subject to change. Visit www.sounddevices.com for the latest documentation.
# Setup Name Setup Description Setup Options
8 Rec: Track Names Used to identify a track name which shows up in
iXML and BWF metadata
• Track A
• Track B
• Track C
• Track D • Mix
• Boom
• <Add New Entry>
• <Load List From INHDD>
• <Save List From INHDD>
9 Rec: Take Name/Number Numeric, auto-incrementing number used for take
identification.
<selectable alpha character + integers up to 32000,
with or without preceding 0’s>
10 Rec: Take Reset Mode Defines when take numbers are reset. Reset brings
take number to <1>.
• Never
- take numbers do not reset
• When scene is changed
- take resets when scene name is changed
• When daily folder changes
- takes reset on new day
• Either scene or daily
- takes reset on either change
11 Rec: Pre-Roll Time Selects the amount of pre-roll time the 744T will
add to the beginning of each file.
0–10 sec. @ 48 kHz
0–5 sec. @ 88.2–96.096 kHz
0–2 sec. @ >96.096–192 kHz
12 Rec: Dither Selects whether to dither is added to 24 bit digital
signals while recording 16 bit files.
• Off
• On (16 bit only)
13 Rec: Timer Start Sets a specific start time/date for unattended
recording. Unit must be powered.
<enter time, date>
14 Rec: Timer Stop Set a specific time/date to stop recording. May be
used with or without the Rec: Timer Start. May be
set before the Timer Start time to temporarily stop
recording and then resume recording with Timer
Start.
<enter time, date>
15 Rec: Record Indicator Sets how the large display looks when the unit
enters record.
• Normal Numbers
• Reverse Numbers
• Flash Numbers
16 Rec: Record Pause Allows a recording to be stopped then continued
without creating a new take or file. Time Code
Mode must be set to Off to enable Record Pause.
• Disabled
• Enabled
17 Input: Routing Allows the user to setup their routing matrix among
all available inputs and tracks. There are preset
routings and three custom routings available.
Pressing the input select key repeatedly will cycle
through all preset routings.
Primarily accessible from the Input Select Key.
• 1 Þ A
• 1 Þ A / 2 Þ B
• 1 Þ A / 1 Þ B
• 1 Þ A,B / 2 Þ A,B
• 1 Þ A / 2 Þ B / 3 Þ C / 4 Þ D
• 1,2,3 Þ A / 1 Þ B / 2 Þ C / 3 Þ D
• Custom Route 1
• Custom Route 2
• Custom Route 3
18
19
Input 1: 48V Phantom
Input 2: 48V Phantom
Enables or disables 48 V phantom power on inputs
1 and 2.
• Off
• On - Mic
• On - Mic and Line
20 Mic Inputs: Limiter Enables or disables the analog input limiter on
input 1 and 2 mic preamps.
• Disabled
• Enabled
21
22
Mic Input 1: Low Cut
Mic Input 2: Low Cut
Enables the high-pass (low cut) filter to reduce
sensitivity to low frequencies.
• Disabled
• Enabled
23
24
Mic Input 1: Low Cut Freq
Mic Input 2: Low Cut Freq
Selection of twelve high-pass filter frequency and
slope combinations for microphone inputs.
• 40, • 80, • 160, • 240 Hz @ 12 dB/oct
• 40, • 80, • 160, • 240 Hz @ 18 dB/oct
• 40, • 80, • 160, • 240 Hz @ 24 dB/oct
25
26
Mic Input 1: Gain Range
Mic Input 2: Gain Range
Selects the sensitivity of the microphone input. Low
sensitivity is used for very loud and/or very hot
microphones.
• Normal
• Low
• Normal, fades to off
• Low, fades to off