Prepare supply hoses, Hose part numbers, Dedicated supply circuit hose – Great Plains YP925TD Assembly Instructions User Manual
Page 7
Great Plains Mfg., Inc.
Installation Instructions
7
2012-22-03
113-870M
Prepare Supply Hoses
Hose Part Numbers
This table has a complete list of hose callouts, part
numbers and descriptions. Your kit contains at most
three different part numbers.
Dedicated Supply Circuit Hose
If the supply hoses rely on a shared circuit, continue at
“Two-Cylinder Shared Supply Circuit” on page 8 or
“Four-Cylinder Shared Supply Circuit” on page 9.
13. Select the two supply hoses
. See the table on
page 6 for the correct part number for the planter.
Refer to Figure 7
14. Select two new:
811-856C CP 1/2FNPT MALE QD
and a quantity of PTFE
a
pipe thread sealant.
15. Apply sealant to the MNPT threads of the hose
fittings. Attach the couplers
to the MNPT ends of
the supply hoses
.
16. Select two new:
800-300C CABLE TIE 2 DIA MIN - ORG
Not shown in figure. Secure one tie to the QD end of
each hose. Wrap it around the hose body at the
crimp. Pull snug. Cut off excess tie.
17. Select one set new:
502-067D HYD HOSE CLAMP LABEL
502-068D HYD HOSE CLAMP BRACKET
802-009C RHSNB 5/16-18X1 1/4 GR5
803-199C NUT HEX FLANGE 5/16-18 PLT
Assemble the clamp near the QD end of the hoses.
The orientation of the arrows does not matter, and
the label side does not need to be up.
Call
-out
Part
Number
Description
811-287C HH3/8R2 030 3/4FJIC 9/16FJIC
811-395C HH1/4R1 072 9/16FJIC 1/2MNPT
811-436C HH1/4R1 156 9/16FJIC 1/2MNPT
811-494C HH1/4R1 190 9/16FJIC
811-637C HH1/4R2 166 9/16FJIC
841-124C HH 1/4 R2 141 9/16FJIC
841-125C HH 1/4 R2 128 9/16FJIC
841-171C HH1/4R2 075 9/16FJIC
841-374C HH1/4R2 085 9/16FJIC
841-397C HH1/4R2 115 9/16FJIC
841-469C HH1/4R2 102 9/16FJIC
841-477C HH1/4R2 140 9/16FJIC
a. See page 20 for pipe sealant information and NPT torque values.
Note: Supply hoses are FJIC-to-FJIC where the markers
are on the lift circuit (North America pull-type
planters only). One FJIC end is connected into the
existing lift circuit.
In a shared 2-cylinder circuit (Model YP425
pull-type only), the marker kit includes tees, which
replace existing elbows.
In a shared 4-cylinder circuit, the marker kit
includes a cross, which replaces existing tees.
Note: Supply hoses are FJIC-to-MNPT where the
markers are on a dedicated hydraulic circuit. The
MNPT end of the hose is connected to a QD
coupler.
Note: A hose clamp and label (see step 17) are provided
in all kits. Their use on hoses shorter than 80 cm
is optional, and is not documented in this manual.
77
78
79
80
81
84
85
86
87
88
89
91
Figure 7
QD Couplers, Clamp
29937
82
62
49
50
52
S
S
82
82
S
51
49
50
52
62