Document Outline

• GDM-W900
• Multiscan®
  • To prevent fire or shock hazard, do not expose the unit to rain or moisture.
  • Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing to qualified personnel only.
  • Table of Contents
  • Introduction
  • Precautions
    • For the customers in UK
  • Connections
    • Step 1: Connect the monitor to the computer.
      • Note
      • Connecting to the HD15 connector
      • Connecting to the 5 BNCs connector
      • For the customers using IBM PC or IBM compatible system which is not compatible with DDC2AB and DDC2B+
      • For the customers using the Macintosh computer
    • Step 2: Connect the power cord.
      • Notice
  • Preset Modes
    • Table of preset modes
      • Recommended horizontal timing conditions
      • Note for Windows* users
  • Selecting the Input Signal
    • 1 Turn on power of the monitor and the computer,
    • 2 Select the input signal.
    • To input the signal from the computer connected to the 5 BNC's connector
    • 3 If necessary, adjust the user controls according to your preference on pages 9 to 15.
    • When you set the INPUT switch to "AUTO"and connect computers to both connectors
    • For the customers using the Windows95
    • To input the signal from the computer connected to the HD15 connector
    • If only one computer is connected or turned on
  • Functions of Controls
    • [T] INPUT switch (page 5)
    • (H RESET button (page 12)
    • [3] OPTION button (pages 8, 9.13,16)
    • [D COLOR button (pages 12,15)
    • [5] SCREEN button (pages 11,14)
    • d] GEOM (geometry) button (pages 10,14)
    • [7] SIZE button (pages 10,14)
    • [8] CENT (center) button (pages 10,14)
    • [9] iii (brightness) -/+ (f/f) buttons (pages 8 -16)
    • 53 (contrast) -/+ (■4"/■►) buttons (pages 8 • 16)
    • 53 POWER SAVING indicator (page 17)
    • 51 (I) power switch and indicator (page 17)
      • OPTION OSD
    • [3]—
    • [T] AC IN connector
    • [2] Video input 1 connector (HD15)
    • U] LANGUAGE (page 8)
    • [U OSD POSITION (page 8)
    • [U OSD MENU (pages 9, 13)
    • g] LOCK (page 16)
    • H] INPUT (pages 5,18)
    • 0 Video input 2 connector (5 BNC)
  • Selecting the OSD Language
    • 1 Press the OPTION button.
    • 2 Press the button to select "LANGUAGE.' — ^ +
    • 3 Press the button to select the desired
    • language.
  • b
    • Changing the OSD Position
      • 1 Press the OPTION button.
      • 2 Press the lii f/f button to select "OSD POSITION".
    • Operating the OSD
      • To select a parameter to adjust or select the setting, press or ♦ button.
      • To adjust or select the settings of the selected parameter, press or ^ button.
  • b
    • Adjustments (Normal mode)
      • Before adjusting
      • 1 Pré» the OPTION button.
      • 2 Press the ■ii-f/'t' button to select "OSD MENU."
      • 3 Press the button to select NORMAL
      • 1 Press theTiT (brightness) ■f/'t button.
      • 2 Press the button again to adjust picture brightness.
      • 1 Press the 3 (contrast) button.
      • 2 Press the button again to adjust picture
      • contrast.
      • 1 Press the CENT button.
  • b
    • For horizontal adjustment
    • 1 Press the SIZE button.
    • 2 For vertical adjustment
  • b
    • For horizontal adjustment
  • b
    • 2 Press the buttons.
    • Convergence
      • 2 Press the button so that the picture edges
      • become straight
      • 1 Press the SCREEN button.
      • 2 Press the button to seiect the parameter you
      • want to adjust referring to the foilowing.
      • Press the button so that the red or blue
      • shadow disappears.
      • 'H CONVERGENCE" (Horizontal convergence)
      • "V CONVERGENCE' (Vertical convergence)
    • Canceling the Moire
      • Press the 0^/*^ button to select "ON" for "CANCEL MOIRE."
      • If the picture becomes unclear
      • 1 Press the button to select "MOIRE ADJ."
      • 2 Press the button to adjust beginning from 0
      • until the moire is minimum.
    • Landing
      • Press the ^4/t button to select "DEGAUSS." Press the 0*^ button.
      • Press the 0*^ button.
      • 5 Press the button to select the position, and
      • adjust by pressing the 0 button.
      • 1 Press the COLOR button.
      • 2 Press the buttons to select a color
      • temperature.
      • Adjusting the color temperature
      • 1 Press the button of the OSD you want to reset to the factory setting.
      • 2 When the parameters are arranged in vertical row in
      • the OSD, select a parameter you want to reset by pressing the buttons.
      • 3 Press the RESET button.
    • Resetting ail adjustment data
      • When there is no OSD displayed, press and hold the RESET button for more than two seconds.
    • Resetting the picture size, position, moire, and geometry* at the same time
      • When there is no OSD displayed, press and hold the RESET button for one second.
    • Adjustments (Expert mode)
      • To cancel the control lock
    • Degaussing the Screen
    • Plug & Play
    • Damper Wire
    • Power Saving Function
    • Input Signal Warning Function
      • [T] Shows the INPUT switch setting.
      • [2] Shows the input signai condition.
    • Specifications
    • Troubleshooting
      • The purpose of Monitor Information Disk
      • Installation
      • Important Notes:
      • A quoi sert la disquette d'informations sur le moniteur
      • Installation
      • Remarques importantes: