Clarion VXZ758R - Manual (Page 16)

16
VXZ758R
280-8178-00
English
Adjusting the bass
(Gain, Frequency, Q-curve)
∗ This function cannot be adjusted when as
follows: “Pro Logic” is set to “ON”, the speaker
system is set to “5.1ch”, DVD/DTS-CD is being
played.
∗ This adjustment can only be performed when
the Z-Enhancer Plus is set to “CUSTOM”.
1. Press the [A-M] button and select “BASS”.
2. Turn the [ROTARY] knob to adjust the bass.
∗ The factory default setting is “BЕ Е Е Е ЕGAIN
0 Γ. (Adjustment range: -6 to +6)
3. Press the [ a]/[d] button to select “BЕ Е Е Е ЕF
60 Γ.
Turn the [ROTARY] knob to select the
frequency.
∗ The factory default setting is “BЕ
Е Е Е ЕF 60Γ.
(Adjustment 60/100/200 Hz)
4. Press the [ a]/[d] button to select “BЕ Е Е Е ЕQ
1 Γ.
Turn the [ROTARY] knob to select the Q-
curve.
∗ The factory default setting is “BЕ
Е Е Е ЕQ 1Γ.
(Adjustment 1/1.25/1.5/2)
5. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the treble
(Gain, Frequency)
∗ This function cannot be adjusted when as follows:
“Pro Logic” is set to “ON”, the speaker system
is set to “5.1ch”, DVD/DTS-CD is being played.
∗ This adjustment can only be performed when
the Z-Enhancer Plus is set to “CUSTOM”.
1. Press the [A-M] button and select “TREBLE”.
2. Turn the [ROTARY] knob to adjust the treble.
∗ The factory default setting is “TЕ Е Е Е ЕGAIN
0 Γ. (Adjustment range: -6 to +6)
3. Press the [ a]/[d] button to select “TЕ Е Е Е ЕF
15k Γ.
Turn the [ROTARY] knob to select the
frequency.
∗ The factory default setting is “TЕ
Е Е Е ЕF 15kΓ.
(Adjustment 10 kHz/15 kHz)
4. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Basic Operations
Adjusting the balance
∗ This function cannot be adjusted when as follows:
“Pro Logic” is set to “ON”, the speaker system
is set to “5.1ch”, DVD/DTS-CD is being played.
1. Press the [A-M] button and select “BAL 0”.
2. Turn the [ROTARY] knob to adjust the
balance of the left and right speakers.
∗ The factory default setting is “BAL 0”.
(Adjustment range: L13 to R13)
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the fader
∗ This function cannot be adjusted when as follows:
“Pro Logic” is set to “ON”, the speaker system
is set to “5.1ch”, DVD/DTS-CD is being played.
1. Press the [A-M] button and select “FAD 0”.
2. Turn the [ROTARY] knob to adjust the
balance of the front and rear speakers.
∗ The factory default setting is “FAD 0”.
(Adjustment range: F12 to R12)
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting MAGNA BASS
EXTEND
The MAGNA BASS EXTEND does not adjust the
low sound area like the normal sound adjustment
function, but emphasizes the deep bass sound
area to provide you with a dynamic sound.
∗ This function cannot be adjusted when as follows:
“Pro Logic” is set to “ON”, the speaker system
is set to “5.1ch”, DVD/DTS-CD is being played.
∗ The factory default setting is “OFF”.
1. Press and hold the [A-M] button for 1 second
or longer to turn on the MAGNA BASS
EXTEND effect. “M-B EX” appears in the
display.
2. Press and hold the [A-M] button for 1 second
or longer to turn off the MAGNA BASS
EXTEND effect. “M-B EX” goes off from the
display.
+VXZ758R_01-09-Eng.p65 05.3.1, 6:02 PM 16