Panasonic PV-4614 - Manual (Page 21)

Cancel a Timer Recording:
Recording in progress
1 Push the VCR POWER button to
release the VCR from timer mode.
2 Push the STOP button within 10
seconds of pushing the VCR Power
button to cancel the recording.
The TiMER indicator goes out in the
Multi Function Display.
Repiace Program Contents:
Recording is not in progress
Push the PROG
button to display
all currently set
programs.
Rotate and push the
Wheel to select and
enter the desired
timer recording.
{See page 20.)
Rotate and push the
Wheel to select and
enter replacement
information.
P OT START STOP CH SPD
1
3 10 8:00 P 9:00P 10 SP
4 SU 9:00P10:00P L SLP
SELECT 1-8:R0frATE WHEEL
ENTER :PUSH WHEEL
CANCEL :PUSH CLEAR KEY
END :PUSH PROG KEY
START STOP CH
7|V/|S
8 SAT 10 :OOP 12 :OOP 125
SLP
ms^ÊmsoEim
BY ROTATING WHEEL
»PUSH CLEAR : PUSH YfHEEL-P
TO END PUSH PROG KEY
Push the PROG button to exit this mode
and return to the normal TV screen.
Review or Ciear Program Contents;
Recording is not in progress
Push the PROG
button to display
all currently set
programs.
Rotate the Wheel to
select the desired
program number.
Push the CLEAR
button to clear the
program.
P DT START STOP CH SPD
2 8 10:OOP12lOOP125 SLP
3 10 8:OOP 9:00P 10 SP
4 SU 9:OOP10:OOP L SLP
SELECT 1-8:H0fTATE WHEEL
ENTER
CANCEL
END
PUSH WHEEL
PUSH CLEAR KEY
PUSH PROG KEY
P OT START STOP CH SPO
D------ :------ :..............
2 8 10;OOP12:OOP125 SLP
3 10 6:OOP 9:OOP 10 SP
4 SU 9: OOP 10: OOP L SLP
SELECT 1-8:ROTATE WHEEL
ENTER :PUSH WHEEL
END :PUSH PROG KEY
Push the PROG button to exit this mode
and return to the normal TV screen.
Timer Recording
Using VCR Buttons
A timer recording can be set up using the buttons on the
VCR. If necessary, the clock can also be set.
Hold down
REC/TIME.
and
Push FF to
enter the
program mode.
START STOP CH
01IHBB3KB0
BY SELECT A/T KEY
NEXT, PUSH SET KEY OR
TO END PUSH PHOG KEY
OSTiON If the clock is not set, pushing these buttons
will display the SET CLOCK screen. In this case,
proceed with steps 2 and 3 to set the clock and
then steps 2“& to set a timer recording.
Once the VCR is in the Program mode, the PLAY,
REC, FF, and REW buttons on the VCR operate only as specified above.
-M t -- set clock
Y”...
BY SELECT A/T KEY
NEXT. PUSH SET KEY OR
TO END PUSH PROG KEY
or C_^_] ► 1
Push REW or PLAY to
make your selection.
(for down) (for up)
Push FF to set
and move on to
the next item.
Push SET (FF) repeatedly to move to a
particular item for setting or correction.
Items to be Set:
• recording DATE
• START time
• STOP time
• CH(annel), or LINE
•SPEED (SP, LP, SLP)
When the program is completed...
(^) jand
Push REC/TIME
and FF to display
program contents.
(at the same time)
To set the next program,
repeat steps 2, 3, and 4 before continuing with step 5.
and
Push REC/TIME and
FF to exit this mode.
(at the same time)
Push POWER off
to set the timer.
TIMER
Multi Function Display
It is not possible to dear a timer program using the VCR
buttons. Please use the Remote Control.
When recording programs via a cable box, make sure the
cable box is left on and tuned to the desired channel.
21