Panasonic PT-AE1000 - Manual (Page 19)

POSITION Menu
Aspect ratio depend on signals
Press ◄ ► to cycle through the aspect ratio
options. The cycle pattern depends on the
connected signals.
VIDEO/
S-VIDEO
PC (RGB)
• 4:3 16:9 -► 14:9 -4 JUST -►
ZOOM1 ZOOM2
• AUTO 4:3 >4 16:9 -4 JUST -
ZOOM
NTSC signal
• 4:3 «4 16:9
• 4:3-f 16:9
VGA or SVGA signals
• Not switchable
WIDE480/600/720/768-2 signals
HOMI
COMPONENT !
(YP b P r )
»4:3-4 16:9
• 16:9 -► H - FIT -4 V - FIT
ZOOM
1 125 (1 080)/50i,
1 125(1 080)/60i,
1 125 (1 080)/50p,
1 125 (1 080)/60p,
1 125 (1 080)/24p, 750 (720)/50p
and 750 (720)/60p signals
• 4:3 -4 16:9 -4 JUST -4 ZOOM
525p (480p) and 625p (576p)
signals
ZOOM1 -4 ZOOM2
625i (576i), 625p (576p)
• AUTO >4 4:3 -4 16:9 -4 JUST -4
ZOOM
525i (480i), 525p (480p)
• 16:9 -4 H - FIT-4 V-FIT
1 125 (1 080)/50i,
1 125 (1 080)/60i,
1 125 (1 080)/50p,
1 125(1 080)/60p,
1 125 (1 080)/24p, 750 (720)/50p,
750 (720)/60p signals I
WSS (Wide Screen Signalling) detects if a
PAL/625p (576p)/625i (576i) signal is input and that
signal has an identification signal, and switch the aspect
ratio to required setting automatically.
You can switch
the system off manually.
36 - E nglish
LENS CONTROL Menu
If the 4 edges of an image is partly dropped, you can use
this function to adjust and project it properly.
Shrink Enlarge
• Setting range: 0 to +10
• OVER SCAN is not available with PC signals.
If the projector is aligned non-perpendicularly to the
screen, or if the projection screen has an angled
surface, you can vertically correct keystone.
Image Operation
• Setting range; -32 to 32
NOTE:
• You can correct the distortion ± 30 degrees from
the vertical plane. For a better quality image,
installing the projector with a minimum of
distortion is recommended,
• Some distortion may be retained for Lens shift
adjustment.
• The distortion of the Main menu screen is not
correctable.
• The result of the keystone correction will affect on
the aspect ratio and the size of the image.
You can use the 2 different test patterns to adjust the focus and zoom of the image. See “Lens shift and positioning”
on page 16.
1. Press ENTER to display test pattern 1 .
• Press
A
▼ to adjust the focus and ◄ ► to adjust the zoom.
2. Press ENTER to display test pattern 2.
• Press A T to adjust the focus and ◄ ► to adjust the zoom.
3. Press ENTER to display the projected image.
• You can confirm the adjustment is fit to the projected image.
4. Press MENU or RETURN to return to the previous menu, or press repeatedly to escape the menu mode.
NOTE: W I 1 ..I
• When the projector and/or the screen is tilted, adjust the focus at the centre of the image. The upper and
lower edge might be out of focus.
• When the image is distorted in keystone, adjust the KEYSTONE in POSITION menu.
You can adjust V - POSITION. H - POSITION, DOT
CLOCK and CLOCK PHASE automatically when
connecting via PC, Press ENTER to adjust these at the
same time.
E nglish - 37