Panasonic PT-AE1000 - Manual (Page 25)

Technical Information
Inquiry commands
Command Control contents Parameter
QPW Power status 000 OFF 001 = ON
QFZ FREEZE status 0 = OFF 1 = ON
QIN Input signal status
Parameter: (page 23)
VID = VIDEO IN
RG1 = P C I N
YUV = COMPONENT IN
SVD = S-VIDEO IN
HD1 = HDM11 IN
HD2 = HDM12IN
SOT = SCART
IN
QOT SLEEP status
0 = OFF 1 = 60 min. 2 = 90 min. 3 = 120 min, 4 = 150 min.
5 = 180 min. 6 = 210 min. 7 = 240 min. (page 25)
QPM PICTURE MODE
status
Parameter: (page 25)
NAT = NATURAL
DYN = DYNAMIC
CN2 = CINEMA2
VID = VIDEO
NOR = NORMAL
CN1 = CINEMA1
CN3 = CINEMA3
QSH SHUTTER status 0 = OFF 1 =ON
QWM WAVEFORM status
Parameter: (page 24)
0 = OFF
1 = FULL SCAN (Y)
2 = FULL SCAN (R)
3 = FULL SCAN (G)
4 = FULL SCAN (B)
5 = SINGLE LINE SCAN (Y)
6 = SINGLE LINE SCAN (R)
7 = SINGLE LINE SCAN (G)
8 = SINGLE LINE SCAN (B)
Basic format
STX
start byte
(02h)
Command ; Parameter ETX
3 bytes 1 byte -
4 bytes End
(03h)
The data streaming from the computer will
start with STX, and proceed to Command,
Parameter and end with ETX. You can
add the required parameter.
• The projector can not receive any command for 10 seconds after the lamp is switched on. Wait 10 seconds
before sending the command.
• If sending multiple commands, check that a response has been received from the projector for one command
before sending the next command.
• When a command which does not require parameters to be sent, the colon (:) is not required.
• If an incorrect command is sent from the personal computer, the ER401 command will be sent from the
projector to the personal computer.
PICTURE Menu ... ...... ................. 31 ►
ri PICTURE MODE.........................................31 ►“I
CONTRAST...................................31 ►
L
BRIGHTNESS............................. 31 ►
COLOUR......................................31 ►
TINT....... ..................................... 31 ►
SHARPNESS...............................32 ►
COLOUR TEMPERATURE...32 ►
DYNAMIC IRIS........................ .....32 ►
WAVEFORM MONITOR.............. 32 ►—
ADVANCED MENU......................32 ►—
MEMORY SAVE..........................33 ►
MEMORY LOAD......................... 33 ►
SIGNAL MODE.............. ...............33 ►
POSITION Menu..................... . 34 ►
iQl H - POSITION................................34 ►
V - POSITION............ ................... 34 ►
DOTCLOCK.... .............................. 34 ►
CLOCK PHASE........................... 34 ►
ASPECT..................................................
35 P—
WSS...... .................................36 ►
OVER SCAN................................ 36 ►
KEYSTONE................................. 36 ►
AUTO SETUP.............................. 36 ►
LENS CONTROL Menu............... 37 ►
^ ZOOM/FOCUS............................... 37 ►
Cable specifications
(When connected to a a personal computer)
OPTION Menu .................. . 38 ►
ШШШШ
%%w^
NC
Projector
NC
NC
NC
INPUT GUIDE............................... 38 ►
OSD DESIGN.............................. 38
OSD POSITION............................. 38 ►
PC (DTE)
BACK COLOUR............................ 38 ►
STARTUP LOGO............................... 38 ►
AUTO SEARCH..................................38 ►
HDMI SIGNAL LEVEL.,............... 38 ►
Technical Information
NORMAL
DYNAMIC
CINEMA1
CINEMA2
CINEMAS
VIDEO
NATURAL
OFF
FULL SCAN(Y)
FULL SCAN(R)
FULL SCAN(G)
FULL SCAN(B)
SINGLE LINE SCAN{Y)
SINGLE LINE SCAN(R)
SINGLE LINE SCAN(G)
SINGLE LINE SCAN(B)
v_
GAMMA
CONTRAST
BRIGHTNESS
COLOUR MANAGEMENT
NR (Noise Reduction)
MPEG NR
CINEMA REALITY
TV-SYSTEM
INSTALLATION.... ........
SLEEP.................... ..........
......... 39 ►—1
......... 39 ►
S
ALTITUDE .. ......... ........... ......... .39 ► fFRONT/DESK 1
LAMP POWER................. ...........39 ► FRONT/CEILiNG
LAMP RUNTIME ............. ...........39 ► REAR/DESK
REAR/CEILING
^ ^
UPPER LEFT
LOWER LEFT
UPPER CENTRE
CENTRE
LOWER CENTRE
UPPER RIGHT
LOWER RIGHT
' Sub-menu items vary according to the selected input signal.
Ц
48 - E nglish
E nglish - 49