Document Outline

• TABLE OF CONTENTS
• Safety Guides
• Unpack and Check Your Carton
  • INSPECT SHIPMENT
  • PARTS DESCRIPTIONS
    • PLAN YOUR INSTALLATION
    • TOOLS NEEDED:
    • WHERE TO INSTALL THE WATER SOFTENER
    • DRAW IN YOUR PIPES AND FITTINGS
    • PIPE, FITTINGS, OTHER MATERIALS NEEDED
  • SOLDERED
  • OUT
• Read Before Beginning Installation
  • BEFORE INSTALLING CHECKS & TESTS
• Assemble
• Port Elbow
• Install Single Bypass Valve
  • ASSEMBLE INLET OUTLET ADAPTORS,
  • OR SINGLE BYPASS VALVE
    • FIG. 7
    • FIG. 8
  • BYPASS VALVE:
  • INLET AND OUTLET THREADED ADAPTORS:
  • INSTALLING BYPASS VALVE, AND/OR INLET AND OUTLET THREADED ADAPTORS
• Install Single Bypass Valve
• Install 3-Valve Bypass
  • INSTALLING 3 VALVE BYPASS AND PIPES
• Locate Water Softener and Connect Pipes
  • POSITION SOFTENER INTO PLACE
  • CONNECT THE SOFTENER
  • MOVE SOFTENER INTO PLACE
  • TYPICAL SOLDERING CONNECTIONS
    • FIG. 15
• Connect Valve and Salt Tank Drains
  • CONNECT THE VALVE DRAIN HOSE
  • CONNECT SALT TANK OVERFLOW TUBING
    • FIG. 16
• Leak Test
  • LEAK TEST
    • 6. Close both cold water faucets.
  • HOUSE MAIN WATER
  • VALVE BYPASS
    • FIG. 19
• Electrical Requirements
  • INSTALL GROUNDING CLAMP BETWEEN THE SOFTENER IN AND OUT PIPES
  • COLD WATER PIPE GROUNDING
    • ELECTRICAL POWER OUTLET FOR YOUR SOFTENER
    • PLUG IN THE TRANSFORMER
  • WATER METER JUMPER WIRE
  • CONNECTING TRANSFORMER
    • FIG. 22
• Install Covers and Restart Water Heater
  • INSTALL COVERS
  • RESTART THE WATER HEATER
    • YOUR PLUMBING INSTALLATION AND ELECTRICAL WORK ARE NOW COMPLETE.
• Program The Timer
  • PROGRAM THE TIMER
    • FIG. 24
    • FIG. 25
• Program The Timer
  • SET PRESENT TIME OF DAY
  • SET WATER HARDNESS NUMBER
  • SET REGENERATION TIME
    • FIG. 26
    • FIG. 27
    • FIG. 28
    • FIG. 29
• Sanitize The Water Softener
  • SANITIZE THE WATER SOFTENER
    • SANITIZE YOUR WATER SOFTENER AS FOLLOWS:
    • You can sanitize the softener with or without salt in the storage tank.
• Adding Salt To The Storage Tank
  • ADDING SALT TO THE STORAGE TANK
  • WATER SOFTENING SALT WITH IRON REMOVING ADDITIVES
• Check
  • FIG. 32
  • EXTRA RECHARGE
  • RECHARGE NOW
  • RECHARGE TONIGHT
  • SALT MONITOR SYSTEM
  • To set this monitor system:
  • ADDING SALT TO STORAGE TANK
  • OPTIONAL SETTINGS:
  • • SALT EFFICIENCY
  • • CLEAN FEATURE
  • • CLEAN FEATURE MINUTES
  • • 97% FEATURE •12/24 HOUR CLOCK
  • • GALLONS / LITERS
  • • MAXIMUM DAYS BETWEEN REGENERATIONS
    • California Efficiency Requirement
    • FIG. 37
    • FIG. 38
    • FIG. 39
    • FIG. 40
    • FIG. 41
    • FIG. 42
    • FIG. 43
  • AVERAGE DAILY GALLONS or LITERS
  • RECHARGE TIME REMAINING AND VALVE POSITION INDICATORS
  • PROGRAM MEMORY
  • ERROR CODE
  • KENMORE’S ULTRA CLEANSING FEATURE
  • SOFT W/VTER SERVICE AND REGENERATION SERVICE
    • REGENERATION
  • WATER FLOW THROUGH THE SOFTENER IN FILL
    • SOFT W/VTER SERVICE AND REGENERATION
  • WATER FLOW THROUGH THE SOFTENER IN BRINING AND BRINE RINSE
  • WATER FLOW THROUGH THE SOFTENER IN BACKWASH
    • SOFT WATER SERVICE AND REGENERATION AUTOMATIC BYPASS
      • ELECTRONICS
  • WATER FLOW THROUGH THE SOFTENER IN FAST RINSE
    • SALT BRIDGE
    • KEEPING THE W/VTER SOFTENER CLEAN
      • NOZZLE & VENTURI
      • 7. Install and tighten the cap, by hand only. Do not overtighten, which may break the cap or housing.
    • IRON FROM RESIN BED
    • PROTECT THE WATER SOFTENER FROM FREEZING
    • CHECKLIST TO HELP YOU SAVE MONEY
    • BYPASS VALVES
    • MODEL 383760 TIMER CODE H32 MODEL 393760 TIMER CODE H 33
      • FIG. 57
  • Pressure Drop (PSI) vs. Flow Rate (GPM)
    • FACEPLATE
      • ALWAYS MAKE THESE INITIAL CHECKS FIRST
        • FIG. 60
        • POSSIBLE PROBLEM
        • CODE
      • PROCEDURE FOR REMOVING ERROR CODE FROM FACEPLATE:
        • FIG. 61
      • TROUBLESHOOTING
      • VALVE POSITION INDICATORS:
        • TIMER PWA REPLACEMENT
        • FIG. 64
      • MANUAL ADVANCE REGENERATION CHECK
        • CYCLE FLOW RATES (GALLONS PER MIN.)
      • ROTARY VALVE SERVICE
      • TO RELIEVE PRESSURE:
      • DISASSEMBLY
      • SERVICING THE VALVE
      • ASSEMBLY
    • W/VTER FLOW THROUGH THE SOFTENER VALVE
    • SERVICE CYCLE
      • SERVICE CYCLE
      • FILL CYCLE
    • BRINING AND BRINE RINSE CYCLE
      • BRINING AND BRINE RINSE CYCLES
    • W/VTER FLOW THROUGH THE SOFTENER VALVE
    • BACKWASH CYCLE
      • BACKWASH CYCLE
    • FAST RINSE CYCLE
      • FAST RINSE CYCLE
  • Your Home
  • Our Home