Kenmore OASIS HT W10026626B - Manual (Page 5)

Alternate Parts
Parts listed are available from your local Sears store or Sears
Service Center. For further information, call
1-800-4-MY-HOME®
Installation spacing for recessed area and closet
installations
(1-800-469-4663).
If You Have: You Will Need to Buy:
Laundry tub or
standpipe taller
than 96" (2.4 m)
Sump pump system (if not already
available)
1" (2.5 cm)
diameter standpipe 2" (5 cm) diameter to 1" (2.5 cm)
diameter standpipe adapter.
Part Number 3363920 and connector kit
Part Number 285835
Overhead sewer Standard 20 gal. (76 L) 39" (99 cm) tall
drain tub or utility sink, sump pump and
connectors (available from local
plumbing suppliers)
Floor drain Siphon break. Part Number 285834;
additional drain hose.
Part Number 8318155 and connector kit.
Part Number 285835
Water faucets
beyond reach of fill
hoses
2 longer water fill hoses:
6 ft (1.8 m) Part Number 76314,
10 ft (3.0 m) Part Number 350008
Lint clogged drain Drain protector. Part Number 367031
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed in a basement, laundry room,
closet, or recessed area. See “Drain System.”
IMPORTANT: Do not install or store the washer where it will be
exposed to the weather.
Proper installation is your responsibility.
You will need:
■ A water heater set to deliver 120°F (49°C) water to the
washer.
■ A grounded electrical outlet located within 4 ft (1.2 m) of
where the power cord is attached to the back of the washer.
See “Electrical Requirements.”
■ Hot and cold water faucets located within 3 ft (90 cm) of the
hot and cold water fill valves, and water pressure of
20-100 psi (138-690 kPa) for best performance.
■ A level floor with a maximum slope of 1'' (2.5 cm) under entire
washer. Installing the washer on carpeting is not
recommended.
■ A sturdy floor to support the washer weight (washer, water
and load) of 315 lbs (143 kgs).
Do not store or operate your washer in temperatures at or below
32°F (0°C). Some water can remain in the washer and can cause
damage in low temperatures. See “Washer Care” for information
on winterizing.
The following spacing dimensions are recommended for this
washer. This washer has been tested for installation with spacing
of 0” (0 cm) clearance on the sides. Recommended spacing
should be considered for the following reasons:
■ Additional spacing should be considered for ease of
installation and servicing.
■ Additional spacing should be considered on all sides of the
washer to reduce noise transfer.
■ For closet installation with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
■ Companion appliance spacing should also be considered.
B
A. Front view
B. Side view
C. Cioset door with vents
‘Required spacing
The washer can be installed using the standpipe drain system
(floor or wall), the laundry tub drain system, or the floor drain
system. Select the drain hose installation method you need. See
“Tools and Parts.”
Standpipe drain system—wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of
2" (5 cm). The minimum carry-away capacity can be no less than
17 gal. (64 L) per minute. A 2" (5 cm) diameter to 1'' (2.5 cm)
diameter standpipe adapter kit is available. See “Tools and
Parts.”
The top of the standpipe must be at least 39" (99 cm) high and no
higher than 96" (244 cm) from the bottom of the washer.