Kenmore 110. 2404# - Manual (Page 12)

5.
6 .
Close the washer lid. The washer will not operate with the lid
open.
Turn the Water Level selector to the correct setting for your
wash load and the type of fabric being washed.
■ Choose a water level that allows the load to move freely
for best fabric care. See “Loading.”
■ You may change to a higher level setting after the washer
has started filling by turning the knob to a different
setting.
7. Set the Water Temperature selector to the correct setting for
the type of fabric and soils being washed. Use the warmest
wash water safe for fabric. Follow garment label instructions.
Water Temp
Hot
Use for
Whites and pastels
Heavy soils
Warm Bright colors
Moderate to light soils
Cold Colors that bleed or fade
Light soils
NOTE: In wash water temperatures colder than 70“F (21 °C),
some detergents do not dissolve well. Soils can be difficult to
remove. Some fabrics can retain wear wrinkles and have
increased pilling (the formation of small lint-like bails on the
surface of garments).
(OPTIONAL) An Automatic Temperature Control (АТС)
electronically senses and maintains a uniform water
temperature by regulating incoming hot and cold water.
■ Even in cold wash, some warm water is let into the
washer to maintain a minimum temperature of
approximately 70®F (21 ®C).
■ Warm wash is maintained at approximately 90°F (32°C).
■ Warm rinse is maintained at approximately 70°F (21 ®C) for
all warm rinse settings. To reduce wrinkling, the warm
rinse is regulated to be cooler than the warm wash.
8 . (RINSE OPTIONS) You can customize your wash by adding
rinse Options to your cycle selections. A cycle will “start”
where you set the Cycle Selector Control (Timer) knob. See
“Selecting a Cycle and Time.” The cycle will “stop” where you
set the Options Control knob. This knob has settings for:
■ One Rinse. Use this option for one rinse after a basic
wash cycle. Rinse & Spin, and Drain & Spin.
■ 2nd Rinse. A 2nd Rinse can be added to the Ultra Clean
and Whitest Whites cycles.
9. Set the Speeds Control knob according to the type of fabric
in the load. See “Selecting Wash/Spin Speeds.”
10. Push in the Cycle Selector Control (Timer) knob and turn it to
the wash cycle you want. Reduce the wash time when using
a small load size setting. See “Selecting a Cycle and Time.”
Pull out the Cycle Selector Control (Timer) knob to start the
washer.
To stop or restart your washer
■ To stop the washer at any time, push in the Cycle Selector
Control (Timer) knob.
■ To restart the washer, close the lid (if open) and pull out
the Cycle Selector Control (Timer) knob.
This section describes the available wash cycles and will help
you make the best cycle selections for your wash loads. Each
cycle is designed for different types of fabric and soil levels.
■ The washer pauses briefly throughout each cycle. These
pauses are normal. Refer to “Normal Sounds” to learn more
about the sounds you may hear during a wash cycle.
■ Refer to “Understanding Washer Cycles” to learn what
happens during a wash cycle.
NOTE: Use this control to choose agitation time and to start the
washer. For heavy soil and sturdy fabrics, use the full time. Use
less time for light soil and delicate fabrics.
P ermanent P ress I
E xpress W ash —e
ULTRA CLEAN lo.^
SUPER---- IS
S uper
—HANDWASH
WHITEST WHITES
wM 0 tatyst-
2 nd rinse s WN fllMSf
/vnuTummsEr fuarosmiT pusntdsidp
Cycle Selector Control (Timer) knob
CATALYST® Cleaning Action
Your washer uses the CATALYST® Cleaning Action to help ensure
better soil and stain removal from your wash load. CATALYST®
Cleaning Action reduces the need for pretreatment and is safe for
all fabrics. CATALYST® Cleaning Action is available in the Whitest
Whites and the Ultra Clean cycles. Although CATALYST® Cleaning
Action is available on all speed control settings, for the best
cleaning performance, use this selection with the Heavy Duty
speed selection.
NOTE: To add CATALYST® Cleaning Action to your wash cycle,
you must set the Cycle Selector Control (Timer) knob on the blue
oval labeled Catalyst®.
12