LAARS M4-Ext - Installation Manual - Manual (Page 14)

14
CONNECTiNg TO THE M4-ExTENSiON PANELS
• The M4-CNC is equipped with a 6-pin phone socket (RS485) to connect to extension panels and XSIG (4-20mA remote set point
Inteface). The M4-Extension is equipped with two 6-pin phone sockets to connect to M4-CNC and an additional M4-Extension.
• Set each Extension to a different letter (EXT-A or EXT-B). The M4-CNC will assign the stage letters based on the extension letter
selected.
• Extension A will operate stages E - J and all the LEDs will be Green. However, Extension B will operate stages K - P and all the
LEDs will be Red. See "M4-Extension Layout" on page 5.
• Configure the Modulating and Sequencing Output Types after connecting the Extension panels to be able to configure their outputs.
See "Modulating Output Type" on page 18
• Only use the cable provided for proper operation.
SYSTEM
A
B
C
D
Full Modulation Sequencing Control
1 2
RUN PROGRAM
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
3 4 5 6 7 8 9 10 11 12 13 15 14 17 16 18 22 20 19 21 24 23 29 25 27 26 28 32 30 31
L N - + + T T O O RS-485 mA GND VLT
SYS A B C D PWR
CUR / VLT
A
- + + mA GND VLT - + + mA GND VLT - + + mA GND VLT + mA
TEMP OUTDOOR
O O
TEMP SYSTEM EXTENSION MODULE CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
CLASS 1 WIRE ONLY.
PROVE /DHW SHUTDOWN /SETBACK
ENCLOSED ENERGY MANAGEMENT EQUIPMENT LISTED 99RA
CAUTION : RISK OF ELECTRIC SHOCK More than one disconnect switch may be required to de-energize the equipment before servicing.
SYSTEM
A
B
C
D
1 2
RUN PROGRAM DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
3 4 5 6 7 8 9 10 11 12 13 15 14 17 16 18 20 19 21 24 23 29 25 27 26 28 32 30 31
L N - + + T T O O RS-485 mA GND VLT
SYS A B C D PWR
CUR / VLT
A
- + + mA GND VLT - + + mA GND VLT + + mA
22
- GND VLT + mA
TEMP OUTDOOR
O O
TEMP SYSTEM EXTENSION MODULE CUR / VLT
B
CUR / VLT
C
CUR / VLT
D PROVE /DHW
SHUTDOWN /TSTAT /SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK More than one disconnect switch may be required to de-energize the equipment before servicing.
F
H
J
Power
CAUTION: Risk of Electric Shock.
More than one disconnect switch may be required
to de-energize the equipment before servicing.
PWR
L N
1 2
E
3 4
F
5 6
G
7 8
H
9 10
I
11 12
EXTENSION MODULE
RS-485
Ext A
INPUT RATINGS:
115VAC 60Hz, 12VA MAX
Use Copper Conductors Only.
OUTPUT RATINGS:
120VAC, 6A RESISTIVE
1A PILOT DUTY, 15A TOTAL
FOR ALL CIRCUITS
E
G
I
Comm
Ext B
K
M
O L
N
P
17 16
VLT mA
CUR / VLT
20 19 16
VLT mA GND
CUR / VLT
23 22 19
VLT mA GND
CUR / VLT
26 25 22
VLT mA GND
CUR / VLT J
13114
K M O L N P E F G H K M L N
15
GND
18
GND
21
GND
24
GND
29 28
VLT mA
CUR / VLT
32 31 16
VLT mA GND
CUR / VLT
27
GND
30
GND
I J O P
M4-Extension A
M4-Ext
FULL MODULATION SEQUENCING EXTENSION
F
H
J
Power
CAUTION: Risk of Electric Shock.
More than one disconnect switch may be required
to de-energize the equipment before servicing.
PWR
L N
1 2
E
3 4
F
5 6
G
7 8
H
9 10
I
11 12
EXTENSION MODULE
RS-485
Ext A
INPUT RATINGS:
115VAC 60Hz, 12VA MAX
Use Copper Conductors Only.
OUTPUT RATINGS:
120VAC, 6A RESISTIVE
1A PILOT DUTY, 15A TOTAL
FOR ALL CIRCUITS
E
G
I
Comm
Ext B
K
M
O L
N
P
17 16
VLT mA
CUR / VLT
20 19 16
VLT mA GND
CUR / VLT
23 22 19
VLT mA GND
CUR / VLT
26 25 22
VLT mA GND
CUR / VLT
J
13 14
K M O L N P E F G H K M L N
15
GND
18
GND
21
GND
24
GND
29 28
VLT mA
CUR / VLT
32 31 16
VLT mA GND
CUR / VLT
27
GND
30
GND
I J O P
M4-Extension B
M4-Ext
FULL MODULATION SEQUENCING EXTENSION
Connecting M4-CNC to
Two M4-Extension
Panels and XSIG
M4-CNC Module
M4-CNC
CONDENSING AND NON-CONDENSING
Cable provided with Extension or 4-20mA EMS Interface
Cable provided with Extension or 4-20mA EMS Interface
4-20 mA EMS
4-20mA INPUT
+ Signal GND
1 2 3
RS485
EXTENSION
CONNECTORS
X SIG
(-)
EMS/BMS Sources
Excitation Voltage
(+)
EMS/BMS
Temperature
Set PointInput
OD= 25 o F SYS= 145 o F
<<A>> B <C> D
100% 52% --- ---
CONNECTiNg TO THE xSig
• The M4-CNC is equipped with a 6-pin phone socket (RS485) to connect to extension panels and XSIG (4-20mA remote set point
Inteface). The XSIG is equipped with two 6-pin phone sockets to connect to M4-CNC and an additional M4-Extension.
• Set Sensor Type to either of the two EMS options. See "Sensor Type" on page 16.
• The interface must be ordered separately.
• Only use the cable provided for proper operation.
LAARS Heating Systems
HT# 059104-00 B