TeeJet TASC-6600 - Manual (Page 4)

IV
TASC-6000, 6300, 6600 98-05010
Rev. - 1
3.0. OPERATION ................................................................................................................................................................ 3-1
3.1. NORMAL START UP AND OPERATION ............................................................................................................ 3-1
3.2. CHANGING ACTIVE BOOM SECTIONS ............................................................................................................. 3-1
3.3. SELECTING DIFFERENT CHEMICAL COMBINATIONS ................................................................................... 3-1
3.4. CHANGING THE APPLICATION RATE “ON THE GO” ...................................................................................... 3-2
3.4.1. CHANGING APPLICATION RATE OF THE MAIN CARRIER .................................................................. 3-2
3.4.2. CHANGING APPLICATION RATE OF THE INJECTED CHEMICALS (TASC 6300/6600 ONLY) .............. 3-2
3.4.2.1. CHANGING ALL INJECTION RATES SIMULTANEOUSLY ............................................................ 3-2
3.4.2.2. ALTERNATE RATES FOR INDIVIDUAL CHEMICALS .................................................................. 3-3
3.5. PRIMING THE INJECTION LINES (TASC 6300/6600 ONLY) ............................................................................... 3-3
3.6. GROUND SPEED OVERRIDE ............................................................................................................................... 3-4
3.7. PRIMING THE MAIN PUMP AND BOOM .......................................................................................................... 3-4
3.8. MANUAL OVERRIDE OF FLOW CONTROL VALVE .......................................................................................... 3-5
4.0. MAINTENANCE ......................................................................................................................................................... 4-1
4.1. FLUSHING AND CLEANING ............................................................................................................................... 4-1
4.2. INJECTION PUMPS ............................................................................................................................................. 4-1
4.2.1. WEEKLY PUMP MAINTENANCE ............................................................................................................. 4-1
4.2.2. SEASONAL PUMP MAINTENANCE ........................................................................................................ 4-2
4.2.3. PERIODIC PUMP MAINTENANCE ........................................................................................................... 4-2
4.3. CONTROL CONSOLE ........................................................................................................................................... 4-2
4.4. GROUND SPEED SENSOR ................................................................................................................................... 4-2
4.5. FLOWMETER ...................................................................................................................................................... 4-2
4.6. FLOW CONTROL VALVE ..................................................................................................................................... 4-3
4.7. WIRING HARNESS .............................................................................................................................................. 4-3
5.0 TASC ERROR MESSAGES, COMMON CONDITIONS AND SOLUTIONS ................................................................. 5-1
6.0. EMERGENCY OPERATIONS ....................................................................................................................................... 6-1
6.1. GROUND SPEED SENSOR FAILURE ................................................................................................................... 6-1
6.2. FLOW CONTROL VALVE FAILURE .................................................................................................................... 6-2
6.3. FLOWMETER FAILURE ...................................................................................................................................... 6-2
A.0 SYSTEM DRAWINGS ................................................................................................................................................A-1
A.1 TASC 6300 SYSTEM WIRING DIAGRAM .........................................................................................................A-2
A.2 TASC 6600 SYSTEM PLUMBING DIAGRAM ....................................................................................................A-3
A.3 REFLOW PLUMBING DIAGRAM ......................................................................................................................A-4
A.4 FLUID OUNCES CONVERSION TABLE .............................................................................................................A-5
A.5 TUBE SELECTION CHART .................................................................................................................................A-6
B.0. SYSTEM OVERVIEW ................................................................................................................................................. B-2
B.1. THE TASC SYSTEM CONTROLS BOTH CARRIER FLOW AND CHEMICAL INJECTION RATES .................. B-2
B.1.1. HOW A TASC-6000, 6300 or 6600 CONTROLS CARRIER APPLICATION RATE .................................... B-2
B.1.2. HOW A TASC-6300 AND 6600 CONTROLS CHEMICAL APPLICATION RATE .................................... B-3
B.2. TASC SYSTEM COMPONENT PARTS .............................................................................................................. B-4
B.2.1. THE TASC CONTROL CONSOLE ............................................................................................................ B-4
B.2.2. FLOWMETER ........................................................................................................................................... B-4
B.2.3. FLOW CONTROL VALVE ......................................................................................................................... B-5
B.2.4. GROUND SPEED SENSOR ........................................................................................................................ B-5
B.2.5. BOOM INTERFACE .................................................................................................................................. B-5
B.2.6. PRECISION INJECTION PUMPS .............................................................................................................. B-5
B.2.7. CHEMICAL CONTAINERS ...................................................................................................................... B-6