Lab.gruppen C Series 88:4 - Manual (Page 3)

1. Important Safety Instructions
i
C Series C 88:4, C 68:4, C 48:4, C 28:4 and C 16:4 Operation Manual rev 2.2.3
1. Important Safety Instructions
Before using the device, be sure to carefully read the Safety Instructions. Keep this document with the device at all times
1.1 Important Safety Instructions
1. Read these instructions.
2. Keep these instructions
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has two blades and
a third grounding prong. The wide blade or the third prong
is provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15. Use the mains plug to disconnect the apparatus from the
mains.
16. WARNING: To reduce the risk of fire of electric shock, do not
expose this apparatus to rain or moisture.
17. Do not expose this equipment to dripping or splashing and
ensure that no objects filled with liquids, such as vases, are
placed on the equipment.
18. Do not connect the unit’s output to any other voltage source,
such as battery, mains source, or power supply, regardless of
whether the unit is turned on or off.
19. Do not remove the top (or bottom) cover. Removal of the cover
will expose hazardous voltages. There are no user serviceable
parts inside and removal may void the warranty.
20. An experienced user shall always supervise this professional
audio equipment, especially if inexperienced adults or minors
are using the equipment.
21. The US National Differences clause 16.3 requires that network
cables must be flame rated VW-1.
To prevent electric shock do not remove top or bottom covers.
No user serviceable parts inside. refer servicing to qualified
service personnel.
Français: à prévenir le choc électrique n’enlevez pas les couvercles.
Il n’y a pas des parties serviceable à l’intérieur. tous reparations
doit etre faire par personnel qualifié seulment.
To completely disconnect this equipment from the ac mains,
disconnect the power supply cord plug from the ac receptacle.
the mains plug of the power supply cord shall remain readily
operable.
Français: Pour démonter complètement l’équipement de
l’alimentation générale, démonter le câble d’alimentation de son
réceptacle. la prise d’alimentation restera aisément fonctionnelle.
This equipment conforms to the requirements
of the EMC Directive 2004/108/EC and the
requirements of the Low Voltage Directive
2006/95/EC.
Standards applied: EMC Emission
EN55103-1, E3
EMC Immunity EN55103-2, E3, with S/N
below 1% at normal operation level.
Electrical Safety EN60065, Class I
This equipment is tested and approved
according to the U.S. safety standard ANSI/
UL 60065 and Canadian safety standard
CSA C22.2 NO. 60065. ETL made the tests
and they are a Nationally Recognized
Testing Laboratory (NRTL).
The lightning bolt triangle is used to alert
the user to the presence of un-insulated
“dangerous voltages” within the unit’s
chassis that may be of sufficient magni-
tude to constitute a risk of electric shock
to humans.
The exclamation point triangle is used to
alert the user to presence of important
operating and service instructions in the
literature accompanying the product.
1.2 Standards
1.3 Explanation of Graphic Symbols