Martin Christ RVC 2-18 CDplus - Manual (Page 29)

RVC 2-18 CD&
6 Operation
Version 04/2012, Rev. 1.3 of 25/11/2013 • sb
29
Translation of the original operating manual
Pos: 102 /20 0 Ch rist/3 70 RVC-BA (S TANDARDMODULE) /06 0 Betri eb/0 60 Bet rieb == == === == == === == == === == == === == == == === == = @ 8\mo d_1 309 426 563 173 _68. docx @ 46 735 @ 1 @ 1
6 Operation
Pos: 103 /20 0 Ch rist/3 70 RVC-BA (S TANDARDMODULE) /06 0 Betri eb/0 60- 001 0 Ers te In bet rieb nah me+ ++ ++ +++ ++ ++ +++ ++ ++ +++ ++ ++ @ 8\ mod _13 094 265 6354 8_6 8.d ocx @ 4674 3 @ 2 @ 1
6.1 Initial start-up
WARNING
Before the initial start-up, please ensure that your RVC is properly set up
and installed (see chapter 5 - "Set-up and connection")
Pos: 104 /01 0 Univ ersal mod ule/ Lee rzeile @ 0\ mo d_12 021 162 445 00_ 0.doc x @ 1 14 @ @ 1
Pos: 105 /20 0 Ch rist/3 70 RVC-BA (S TANDARDMODULE) /06 0 Betri eb/0 60- 002 0 Einsc halte n+ +++ ++ ++ +++ ++ ++ +++ ++ ++ +++ ++ ++ ++ +++ ++ ++ @ 8\ mod _13 0942 656 454 8_6 8.doc x @ 4 676 7 @ 2 @ 1
6.2 Switching the RVC on
• Press the mains power switch on the right-hand side of the unit.
The CD
plus
control unit performs a self-test and an initialisation. This may
take several seconds.
• Follow the safety instructions and hazard warnings !
Pos: 106 /01 0 Univ ersal mod ule/ Lee rzeile @ 0\ mo d_12 021 162 445 00_ 0.doc x @ 1 14 @ @ 1
Pos: 107 /20 0 Ch rist/3 70 RVC-BA (S TANDARDMODULE) /06 0 Betri eb/0 60- 003 0 Ö ffne n un d Schlie ßen des D eckels @ 8\ mod _13 094 270 445 54_6 8.d ocx @ 467 91 @ 2 @ 1
6.3 Opening and closing the lid
The lid can be opened if the rotor chamber is aerated and if the rotor is at a
standstill. The rotational vacuum concentrator cannot be started if the lid is
open.
• Select "mode" with the left-hand function key.
• Select "Open lid" with the up and down keys.
• To close, press slightly on the lid until both locks are locked.
DANGER
Do not place your fingers between the lid and the housing when closing
the lid. Risk of crushing!
Pos: 108 /01 0 Univ ersal mod ule/ Lee rzeile @ 0\ mo d_12 021 162 445 00_ 0.doc x @ 1 14 @ @ 1
Pos: 109 /20 0 Ch rist/3 70 RVC-BA (S TANDARDMODULE) /06 0 Betri eb/0 60- 004 0 Eins etzen von R oto ren und Zu beh ör- -- --- -- --- --- -- --- -- --- -- --- --- -- --- - @ 8\m od_ 1309 498 541 224 _68. docx @ 46 808 @ 2 @ 1
6.4 Installation of rotors and accessories
Pos: 110 /20 0 Ch rist/3 70 RVC-BA (S TANDARDMODULE) /06 0 Betri eb/0 60- 004 0-0 010 Einsetz en v on Wink elrot ore n @ 8\m od_ 130 9496 686 889 _68. docx @ 46 801 @ 3 @ 1
6.4.1 Installation of angle rotors
• Only use inserts that are suitable for the rotor (see chapter 11.1 -
"Rotor program").
• Always load the opposite inserts of the rotors with the same accessories
and fill to avoid imbalance.
• Push the loaded rotor onto the rotor shaft until it reaches the stop.
NOTE
Depending on the version, up to three rotors can be pushed onto the rotor
shaft at the same time.