Dot Hill Systems II 200 FC User Manual
Dot Hill Systems Hardware
Advertising
Table of contents
Document Outline
- Contents
- Figures
- Tables
- Preface
- Product and Architecture Overview
- Site Planning
- Unpacking Your Array
- Connecting Your Array
- 4.1 Converting Your Front Bezel Locks So the Keys Cannot Be Removed
- 4.2 RAID Array Connections
- 4.3 Connecting the Chassis to AC Power Outlets
- 4.4 Connecting the Chassis to DC Power Outlets
- 4.5 Cabling to Expansion Units
- 4.6 Setting Loop IDs on Expansion Units
- 4.7 Powering Up and Checking LEDs
- 4.8 Reviewing Channels, Ports, and SFPs
- 4.9 Establishing Communications With An Array
- 4.10 Configuring a Host COM Port to Connect to a RAID Array
- 4.11 Manually Setting a Static IP Address
- 4.12 Setting Up Out-of-Band Management Over Ethernet
- 4.13 Scaling a SANnet II 200 Fibre Channel Array Into a High-Capacity Configuration
- 4.14 Adding an Expansion Unit to an Existing RAID Array
- 4.15 Connecting Ports to Hosts
- 4.16 Power-On Sequence
- 4.17 Powering Off the Array
- Configuration Overview
- Checking LEDs
- Maintaining Your Array
- Troubleshooting Your Array
- SANnet II 200 FC, SATA, and SATA SE Array Specifications
- Using a Standalone JBOD Array (SANnet II 200 FC Array Only)
- B.1 Supported Configurations (JBOD Arrays)
- B.2 Supported Operating Systems (JBOD Arrays)
- B.3 Supported Host Platforms and Connection Methods (JBOD Arrays)
- B.4 Known Limitations Affecting SANnet II 200 FC JBOD Arrays
- B.5 Using SANnet II Family Software Monitoring and Management Tools with JBOD Arrays
- B.6 Setting the Loop ID on a SANnet II 200 FC JBOD Array
- B.7 Connecting SANnet II 200 FC JBOD Arrays
- B.8 Enabling SANnet II 200 FC JBOD Array Support
- B.9 Downloading Firmware to Disk Drives in a JBOD
- B.10 Resizing LUNs Greater Than 1 Tbyte
- B.11 Troubleshooting SANnet II 200 FC JBOD Arrays
- B.12 Converting a JBOD to a RAID array
- Failed Component Alarm Codes
- Cable Pinouts
- Configuring a Sun Server Running the Solaris Operating System
- Configuring a Microsoft Windows Server
- Configuring a Linux Server
- G.1 Setting Up the Serial Port Connection
- G.2 Accessing the Firmware Application From a Linux Server
- G.3 Checking the Adapter BIOS
- G.4 Multiple LUN Linux Configuration
- G.5 Making an ext3 File System for Linux
- G.6 Creating a File System
- G.7 Creating a Mount Point and Mounting the File System Manually
- G.8 Mounting the File System Automatically
- G.9 Determining the Worldwide Name for Linux Hosts
- Configuring an IBM Server Running the AIX Operating System
- H.1 Setting Up a Serial Port Connection
- H.2 Accessing the Firmware Application From an IBM Server Running AIX
- H.3 Identifying the Device on Which You Will Create a Logical Volume
- H.4 Using SMIT to Enable an AIX Host to Recognize New LUNs
- H.5 Creating a Volume Group
- H.6 Creating a Logical Volume
- H.7 Creating a File System
- H.8 Mounting the New File System
- H.9 Verifying That the New File System Is Mounted
- H.10 Determining the Worldwide Name for IBM Servers Running AIX
- Configuring an HP Server Running the HP-UX Operating System
- I.1 Setting Up a Serial Port Connection
- I.2 Accessing the Firmware Application From an HP Server Running HP-UX
- I.3 Attaching the Disk Array
- I.4 Logical Volume Manager
- I.5 Definitions of Common Terms
- I.6 Creating a Physical Volume
- I.7 Creating a Volume Group
- I.8 Creating a Logical Volume
- I.9 Creating an HP-UX File System
- I.10 Mounting the File System Manually
- I.11 Mounting the File System Automatically
- I.12 Determining the Worldwide Name for HP-UX Hosts
- Index