DFI HM961-HM86 - Manual (Page 24)

www.dfi .com Chapter 3 Hardware Installation
24
Chapter 3
Signal Pin# Pin Type Pwr Rail /Tolerance HM961-QM87/HM86 Carrier Board Description
SPI_CS# B97 O CMOS 3.3V Suspend/3.3V
Connect a series resistor 33ȟ to Carrier Board
SPI Device CS# pin
Chip select for Carrier Board SPI - may be sourced from chipset SPI0 or SPI1
SPI_MISO A92 I CMOS 3.3V Suspend/3.3V Connect a series resistor 33ȟ to Carrier Board Data in to Module from Carrier SPI
SPI_MOSI A95 O CMOS 3.3V Suspend/3.3V Connect a series resistor 33ȟ to Carrier Board Data out from Module to Carrier SPI
SPI_CLK A94 O CMOS 3.3V Suspend/3.3V Connect a series resistor 33ȟ to Carrier Board Clock from Module to Carrier SPI
SPI_POWER A91 O 3.3V Suspend/3.3V
Power supply for Carrier Board SPI – sourced from Module – nominally
3.3V. The Module shall provide a minimum of 100mA on SPI_POWER.
Carriers shall use less than 100mA of SPI_POWER. SPI_POWER
shall only be used to power SPI devices on the Carrier
BIOS_DIS0# A34
BIOS_DIS1# B88
Signal Pin# Pin Type Pwr Rail /Tolerance HM961-QM87/HM86 Carrier Board Description
VGA_RED B89 O Analog Analog PD 150 TO GND PD 150R,connect to VGA connector with EMI Red for monitor. Analog output
VGA_GRN B91 O Analog Analog PD 150 TO GND PD 150R,connect to VGA connector with EMI Green for monitor. Analog output
VGA_BLU B92 O Analog Analog PD 150 TO GND PD 150R,connect to VGA connector with EMI Blue for monitor. Analog output
VGA_HSYNC B93 O CMOS 3.3V / 3.3V Connect to VGA connector with a3.3V Buffer Horizontal sync output to VGA monitor
VGA_VSYNC B94 O CMOS 3.3V / 3.3V Connect to VGA connector with a 33V Buffer Vertical sync output to VGA monitor
VGA_I2C_CK B95 I/O OD CMOS 3.3V / 3.3V PU 2.2K TO 3V3 Connect to VGA connector with a 3.3V to 5V DDC clock line (I2C port dedicated to identify VGA monitor capabilities)
VGA_I2C_DAT B96 I/O OD CMOS 3.3V / 3.3V PU 2.2K TO 3V3 Connect to VGA connector with a 3.3V to 5V DDC data line.
Signal Pin# Pin Type Pwr Rail /Tolerance HM961-QM87/HM86 Carrier Board Description
SER0_TX A98 O CMOS 3.3V/5V PD 4.7K TO GND General purpose serial port 0 transmitter
SER0_RX A99 I CMOS 3.3V/5V PU 47K TO 3V3 General purpose serial port 0 receiver
SER1_TX A101 O CMOS 3.3V/5V PD 4.7K TO GND General purpose serial port 1 transmitter
SER1_RX A102 I CMOS 3.3V/5V PU 47K TO 3V3 General purpose serial port 1 receiver
Signal Pin# Pin Type Pwr Rail /Tolerance HM961-QM87/HM86 Carrier Board Description
I2C_CK B33 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K TO 3V3_DU_EC General purpose I2C port clock output
I2C_DAT B34 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K TO 3V3_DU_EC General purpose I2C port data I/O line
SPKR B32 O CMOS 3.3V / 3.3V
Output for audio enunciator - the "speaker" in PC-AT systems.
This port provides the PC beep signal and is mostly intended for
debugging purposes.
WDT B27 O CMOS 3.3V / 3.3V Output indicating that a watchdog time-out event has occurred.
FAN_PWNOUT B101 O OD CMOS 3.3V / 12V Fan speed control. Uses the Pulse Width Modulation (PWM) technique to control the fan's RPM.
FAN_TACHIN B102 I OD CMOS 3.3V / 12V PU 10K TO 3V3 Fan tachometer input for a fan with a two pulse output.
TPM_PP A96 I CMOS 3.3V / 3.3V PU 10K TO GND
Trusted Platform Module (TPM) Physical Presence pin. Active high.
TPM chip has an internal pull down. This signal is used to indicate
Physical Presence to the TPM.
Serial Interface Signals Descriptions
Miscellaneous Signal Descriptions
SPI Signals Descriptions
I CMOS NA
Selection straps to determine the BIOS boot device.
The Carrier should only float these or pull them low, please refer to
COM Express Module Base Specification Revision 2.1 for strapping options of BIOS disable signals.
VGA Signals Descriptions