Smithco Super Star Diesel 43-500 (sn 14560 – 14579) Parts & Service Manual - Manual (Page 79)

B-5
Center Attachment
42-750 CART PATH AND SIDEWALK EDGER PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 HCP-12-200 Clevis Pin, 1 /
2
x 2 2
2 HHP-.177 Bridge Pin, .177 x 3.75 3
3 HCP-58-250 Clevis Pin, 5 /
8
x 2 1 /
2
1
4 42-203 Attachment Lift Assembly 1
5 42-758 Brush 1
6 42-754 Edger Mount 1
7 HB-38-16-125 Bolt, 3 /
8
-16 x 1¼ 3
HNFL-38-16 Flange Whiz-Lock Nut, 3 /
8
-16 3
HW-38 Flat Washer, 3 /
8
3
8 HG-14-28-180 Grease Fitting, 1 /
4
- 28 x 180°( Part of 42-755 ) 2
9 42-755 Edger Arm 1
10 10-134 Spacer 1
11 HB-38-16-250 Bolt, 3 /
8
- 16 x 2½ 3
HNFL-38-16 Flange Whiz-Lock Nut, 3 /
8
-16 3
12 60-123 Shock Absorber 1
13 HW-38 Flat Washer, 3 /
8
3
14 48-109 Spring 1
15 42-757 Spring Mount 1
16 HNTL-34-16 Lock Nut, ¾ - 16 1
17 HMB-34-10 Machine Bushing, ¾ x 10GA 2
18 42-756 Edger Fork 1
19 HB-58-11-325 Bolt, 5 /
8
- 11 x 3¼ 1
HNCL-58-11 Center Lock Nut, 5 /
8
-11 1
20 60-325 Spacer 1
21 HMB-58-14 Machine Bushing, 5 /
8
x 10GA 3
22 42-752 Edger Blade 1
23 76-298 Spacer 2
24 HB-14-20-075 Bolt, ¼ - 20 x ¾ 3
HNFL-14-20 Flange Whiz-Lock Nut, ¼ - 20 3
25 42-759 Brush Holder 1
26 HP-18-150 Cotter Pin 1 /
8
x 1 1 /
2
1
27 HMB-100-14 Machine Bushing, 1 x 14GA 2
INSTALLATION INSTRUCTIONS
For your convenience and ease of installation, a major set of components are pre-assembled at the
factory. This is the "Edger Assembly" and includes Reference #'s 11 thru 25.
1. Slide Attachment Lift Assembly (Ref 4) under machine and attach using (2) ½ x 2" Clevis Pins (Ref 1) &
(2) Bridge Pins (Ref 2). Connect the free end of the hydraulic cylinder to the Attachment Lift Assembly
(Ref 4) as illustrated using the
5 /
8
x 2½ Clevis Pin (Ref 3) & (1) Bridge Pin (Ref 2).
2. Attach the Edger Mount (Ref 6) to the Attachment Lift Assembly (Ref 4) using (3) 3 /
8
- 16 x 1¼ bolts,
3 /
8
Flat Washers and 3 /
8
-16 Whiz-Lock Nuts (Ref 7).
3. Now slide (1) 1" Machine Bushing (Ref 27) on the Edger Mount's (Ref 6) pin. Next install the "Edger
Assembly" (see sidebar) onto the pin. Place the second 1" Machine Bushing (Ref 27) on the pin. Secure
with a
1 /
8
x 1½ Cotter Pin (Ref 26).
4. Slide (1) 3 /
8
" Flat Washer onto (1) 3 /
8
- 16 x 2½ bolt & insert this in the free end of the Shock Absorber
(Ref 12). Next, slide the Spacer (Ref 10) onto the bolt and use (1) 3 /
8
-16 Whiz-Lock Nut to secure the
Shock Absorber (Ref 12) to the Edger Mount (Ref 6) as illustrated.
5. Grease all Grease Fittings (Ref 8) and check all fasteners for proper installation.