Alinco EJ-50U - Manual (Page 8)

8
ECHO E ON ON/OFF Activates echo back of your keystrokes on the
computer screen
3-2-4
EPATH EPATH N/A Call1, --,
Call7 Sets digipeater list to be replaced while using
UISSID 8-3-9
EXTCLR EXTC N/A N/A Clears the Message Board 10-1-6
FILE FI N/A N/A Displays all messages on the Message Board. 10-2-1
FIRMRNR FIR OFF ON/OFF In RNR frame reception, TNC waits to transmit
until next frame reception.
4-4-11
FLOVER FL 0 0-120 Sets time when the TX/RX buffers are cleared after
the host’s buffer has filled up. A unit of 1mS.
3-2-8
FLOW F ON ON/OFF When on, when you start keyboard activity, TNC
output to the terminal stops.
3-2-5
FRACK FR 3 0-15 The re-try waiting period in units of 1 second. 4-4-7
FULLDUP FU OFF ON/OFF To select Full-Duplex or Semi- Duplex mode. Not
useful in a monoband transceiver
4-2-9
GBAUD GB 4800 4800/9600 Sets the data communication rate with the GPS
receiver
5-6-1
GPSSEND GPSS N/A 159
characters
Use to output up to 159 characteristics to initialize
the GPS. This data cannot be memorized. 5-6-10
GPSTEXT GPST $PNTS 6 characters Sets the data string to be sent into LTEXT from the
GPS.
5-6-6
HBAUD HB 1200 1200/9600 Changes the data rate of communications over the
radio (1200 or 9600bps)
4-1-1
HEALLED HEAL OFF ON/OFF Tests LEDs on TNC 7-5-1
HID HI ON ON/OFF When ON, sends ID after packets are digipeated
through your station
8-1-3
ID I N/A N/A Transmits ID immediately. 8-1-4
KILL KI ON ON/OFF Deletes Messages on the message board 10-2-6
KISS KISS OFF ON/OFF TNC will enter the KISS mode after the next
boot-up.
6-5-1
LCSTREAM LCS ON ON/OFF Allows lower case letter to be used after stream
switch command is sent
9-1-4
LIST LI N/A N/A Displays all messages except private messages
being sent from one station to another
10-2-2
LOCATION LOC EVERY 0 EVERY/AF
TER
n(0-250)
Sets the time interval of GPS data transmissions
(stored in LTEXT) in 10 second increments. 5-6-3
LOG LOG N/A N/A Displays a list of stations that connected to the
Message Board.
10-1-7
LPATH LPA GPS Call (VIA
call1,call2
,--,call8)
Sets the outgoing path of GPS data. (Including
DIGIpeater(s) used). 5-6-2
LTEXT LT N/A 159
characters
The GPS data buffer. 5-6-4
LTMON LTM 0 0-250 Displays the LTEXT message as if it were received
as a beacon signal, in preset intervals.
5-6-5
MAIL MAI OFF ON/OFF When ON, LED indicates when messages are
received 10-3-3
MALL MA ON ON/OFF Monitor all stations/not connected stations 4-7-4
MAXFRAME MAX 4 1-7 The maximum number of packet frames the unit
can transmit at once 4-6-7
MBOD MB OFF ON/OFF Enables use of Message Board 10-1-1
MCOM MCOM OFF ON/OFF TNC monitors all I frames. 4-7-2
MCON MC OFF ON/OFF Monitor (or not monitor) other stations while you
are connected. 4-7-3
MINE MI N/A N/A Displays the list of messages addressed to my
callsign from the Message Board. 10-2-3