Sealey SWSKIT User Manual
Page 5
Sensor
Door/Window Sensor
Door/Window Sensor
Motion Sensor
Zone
1
2
8
Status (MODE)
ARM
ARM
ARM
A. Adjusting Exit Delay
The default setting of the Smart Panel allows the user 20 seconds to exit the property before the alarm is
ARMED. However, this Exit Delay can be adjusted to between 10 and 60 seconds as follows:
B. Adjusting Entry Delay
The default setting of the Smart Panel allows the user 30 seconds to enter the property and DISARM the alarm
before it is triggered. However, this Entry Delay can be adjusted to between 10 and 60 seconds as follows:
Keys
(1234/
4-digit PIN)
+
Description
Enter the default PIN “ 1 2
3 4 ” OR your new 4-digit
PIN for setting followed by
The Smart Panel will display the below image:
Note
1
2
3
4
(1234/
4-digit PIN)
+
*To make sure you are in STANDBY mode:
- Enter the default PIN “ 1 2 3 4 ” OR your new 4-digit PIN
- Press
- The Smart Panel will display the image below when you are
in STANDBY mode:
(One beep indicates that you entered a valid PIN, three
beeps indicate that an invalid operation was performed).
Press to complete the
setting
Keys
(1234/
4-digit PIN)
+
Description
Note
1
*To make sure you are in STANDBY mode:
- Enter the default PIN “ 1 2 3 4 ”
OR your new 4-digit PIN
- Press .
- The Smart Panel will display the below image while you were
in STANDBY mode:
(One beep indicates that you entered a valid PIN, three
beeps indicate that an invalid operation was performed).
- LCD display flashes with “2”
- Re-enter the new 4-digit PIN
- Press for final confirmation
(One beep indicates that you entered a valid PIN, two beeps
indicate that an invalid operation was performed).
5 New 4-digit
PIN +
Re-enter new PIN for
followed by for final
confirmation
3.2 Transmitting an emergency (Panic) alarm
3.2.1 Using the Panic alarm
Pressing & buttons together on the Keypad or Key Fob Remote Control will immediately transmit an
alarm signal to the Smart Panel, activating the siren, and transmitting an alarm signal to any optional response
devices (Auto Dialer & Outdoor Bell Box), to request emergency assistance
To disarm the Panic alarm
On the Smart Panel: Enter your 4-digit PIN followed by to exit from the Panic alarm.
On the Key Fob Remote Control: Press to exit from the Panic alarm.
3.2.2 Using the Panic alarm without activating the siren
If you are forced to disarm the system, enter the Duress Password to stop the siren from sounding. The Smart
Panel will then silently transmit an alarm signal to the optional response devices (Auto Dialer & Outdoor Bell
Box) to request emergency assistance.
Duress Password:
Enter the default 4-digit PIN + ( + ) +
OR
Enter your personalised 4-digit PIN+ +
3.3 Operating different modes
The system has 4 operating modes (STANDBY, ARM, ALERT, and HOME) to suit individual requirements.
These modes can be set as follows:.
3.3.1 STANDBY mode
If in STANDBY mode, the Smart Panel is prepared for mode selection.
You must be in STANDBY
mode before turning to
ARM mode
3.3.2 ARM mode
When in ARM mode, the Smart Panel siren will sound and the Smart Panel flashes RED every 1.5 seconds
when the system is triggered.
ARM mode default setting:
You must be in STANDBY
mode before adjusting the
Exit Delay
Press then (as
many times as required)
to set the new Exit Delay
- When is pressed the first time the Smart Panel flashes
with the number of seconds currently set for the Exit Delay
(The factory default setting is 20 seconds)
- Each time is pressed the Exit Delay is increased by a
further 10 seconds between the adjustable range of 10 to 60
seconds
- The Exit Delay time on the LCD display will flash until the
setting is completed
Confirm the setting and return the Smart Panel to STANDBY
by pressing
Keys
(1234/
4-digit PIN)
+
Description
Note
1
*To make sure you are in STANDBY mode:
- Enter the default PIN “ 1 2 3 4 ” OR your new 4-digit PIN
- Press
- The Smart Panel will display the image below when you are
in STANDBY mode:
(One beep indicates that you entered a valid PIN, three
beeps indicate that an invalid operation was performed).
You must be in STANDBY
mode before adjusting the
Entry Delay
- 7 -
- 6 -