Extron electronic IPL T S Series - Manual (Page 72)

IPL T S Series • Specifications, Part Numbers, Accessories A-2
Specifications, Part Numbers, Accessories
Specifications
Ethernet control interface
Connectors ..................................... 1 RJ-45 female connector
Data rate ......................................... 10/100Base-T, half/full duplex with autodetect
Protocols ......................................... ARP, DHCP, ICMP (ping), TCP/IP, UDP/IP, Telnet, HTTP, SMTP
Default settings .............................. Link speed and duplex level = autodetected
IP address = 192.168.254.254
Subnet mask = 255.255.0.0
Gateway = 0.0.0.0
DHCP = off
Web server ...................................... Up to 200 simultaneous sessions
7.25 MB nonvolatile user memory
Program control ............................. Extron's Simple Instruction Set (SIS ™ )
Global Viewer requirements ........ Microsoft ® Internet Explorer ver. 6 or higher
Serial control interface
Quantity/type
IPL T S1 ............................... 1 RS-232-only
IPL T S2 ............................... 2 RS-232/RS-422/RS-485 configurable serial
IPL T S4 ............................... 4 RS-232/RS-422/RS-485 configurable serial
IPL T S6 ............................... 2 RS-232/RS-422/RS-485 configurable serial
4 RS-232-only
Connectors
IPL T S1 ............................... (1) 9-pin male D
IPL T S2 ............................... (2) 9-pin male D and (1) 3.5 mm captive screw connector, 5 pole
IPL T S6 ............................... (2) 9-pin male D and (1) 3.5 mm captive screw connector, 10 pole
IPL T S4 ............................... (4) 9-pin male D
Baud rate and protocol ................. 300 to 115200 baud
Default settings (adjustable): 9600 baud, 8 data bits, 1 stop bit, no parity
Pin configurations
Serial, 9-pin D (IPL T S1)
RS-232 ......................... 2 = RX, 3 = TX, 5 = GND, 7 = RTS, 8 = CTS
Serial, 9-pin D (IPL T S2, IPL T S4)
RS-232 (default) ......... 2 = RX, 3 = TX, 5 = GND, 7 = RTS, 8 = CTS
RS-422 ......................... 2 = RX-, 3 = TX-, 5 = GND, 7 = TX+, 8 = RX+
RS-485 ......................... 2&3 (tied together) = data-, 5 = GND, 7&8 (tied together) = data+
Serial, 5-pole captive screw
IPL T S2 ....................... COM1: pin 1 = TX, 2 = RX, 3 = GND
COM2: pin 4 = TX, 5 = RX, 3 = GND
Serial, 10-pole captive screw
IPL T S6 ....................... COM3: pin 1 = TX, 2 = RX, 3 = GND
COM4: pin 4 = TX, 5 = RX, 3 = GND
COM5: pin 6 = TX, 7 = RX, 8 = GND
COM6: pin 9 = TX, 10 = RX, 8 = GND
General
Power .............................................. Supplied by an included external power supply.
External power supply ................. 100 VAC to 240 VAC, 50/60 Hz, external; to 12 VDC, 2 A, regulated
Power input requirements ........... 12 VDC, 0.5 A
Temperature/humidity ................ Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing