Honeywell CHRONOTHERM T8602D - Manual (Page 13)

T8600D, T8601D AND T8602D CHRONOTHERM ® IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1 13
Period Start Time Heat Setpoint Cool Setpoint Fan Setting
Sunday
Wake [6:00 AM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Leave [8:00 AM] [62°F (16.5°C)] [85°F (29.5°C)] [Auto]
Return [6:00 PM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Sleep [10:00 PM] [62°F (16.5°C)] [82°F (28°C)] [Auto]
Table 9. Default Time, Setpoints and Fan Settings (continued).
2. Press Day until the desired day is displayed.
M10318
Time Set Program
System Fan
Run Program
Hold Temp
Set Current Day/Time Wake Leave Return Sleep
Day
Day
Heat/Cool Settings
Daylight Time Copy
Heat
Auto
System Fan
Wake
Mon
AM
Set Program Start Time Setting
Heat
3. Press Time ▲ ▲ or Time ▼ ▼ until the desired Wake time is
displayed.
NOTE: The program times are in fifteen minute
intervals. (Example: 8:00, 8:15, 8:30).
M10319
Time Set Program
System Fan
Run Program
Hold Temp
Set Current Day/Time Wake Leave Return Sleep
Day Heat/Cool Settings
Daylight Time Copy
Heat
Auto
System Fan
Wake
Mon
AM
Set Program Start Time Setting
Heat
Time
4. Press increase ▲ or decrease ▼ key until the desired
Wake temperature is displayed.
NOTE: The setpoint temperature range is 40 to 90 ° F
(7 to 31 ° C) for heating and 45 to 99 ° F (9 to
37 ° C) for cooling.
M10320
Time Set Program
System Fan
Run Program
Hold Temp
Set Current Day/Time Wake Leave Return Sleep
Day Heat/Cool Settings
Daylight Time Copy
Heat
Auto
System Fan
Wake
Mon
AM
Set Program Start Time Setting
Heat
NOTE: Press Fan to modify fan operation. Auto means
the fan will run only when the heating or
cooling equipment is operating. On means the
fan will run continuously for the entire period.
5. Press Heat/Cool Settings to switch to other system
temperature setpoint.
NOTE: The program times are the same for both
heating and cooling.
M10321
Time Set Program
System Fan
Run Program
Hold Temp
Set Current Day/Time Wake Leave Return Sleep
Day Heat/Cool Settings
Heat/Cool
Settings
Daylight Time Copy
Auto
System Fan
Wake
Mon
AM
Cool
Set Program Start Time Setting
Heat
6. Press increase ▲ or decrease ▼ key until the desired
temperature setpoint is displayed.
Time Set Program
System Fan
Run Program
Hold Temp
Set Current Day/Time Wake Leave Return Sleep
Day Heat/Cool Settings
Daylight Time Copy
Auto
System Fan
Wake
Mon
AM
Cool
Set Program Start Time Setting
Heat
M10322
7. Press Leave, Return or Sleep and repeat steps 3, 4, 5
and 5 for programming the rest of the day. The first day
is now programmed.
M10323
Time Set Program
System Fan
Run Program
Run
Program
Hold Temp
Set Current Day/Time Wake Leave Return Sleep
Day Heat/Cool Settings
Daylight Time Copy
Auto
System Fan
Wake
Room
AM
DST
Tue
Heat
Copying a Day
NOTE: The thermostat must be in the program mode to use
the copy feature. Go to step 2 if the thermostat is
already in the program mode.
1. Press Wake.
M10324
Time Set Program
System Fan
Run Program
Hold Temp
Set Current Day/Time Wake Wake Leave Return Sleep
Day Heat/Cool Settings
Daylight Time Copy
Heat
Auto
System Fan
Wake
AM
Tue
Set Program Start Time Setting
Heat
IMPORTANT
Repeat steps 1 through 7 for each day of the week
that has a different program than the first day. Refer
to Copying a Day section to copy any program day to
another.
8. Press Run Program when all days are programmed.
2. Press Day to select the day to be copied if different
from the day displayed.
M10325
Time Set Program
System Fan
Run Program
Hold Temp
Set Current Day/Time Wake Leave Return Sleep
Day
Day
Heat/Cool Settings
Daylight Time Copy
Heat
Auto
System Fan
Wake
Mon
AM
Set Program Start Time Setting
Heat