Honeywell Chronotherm IV T8611G - Manual (Page 7)

69-0936—1 7
T8611G CHRONOTHERM ® IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTATS
Aux Ht
Heat
Auto
System Fan
Off Auto
Wake
Mon
Wait
In
Room
Outdoor
%Humid
Auto
Sav
AM
PM
Hold for
Cool
Repl Batt
On
Recovery
DST
Cool
TueWedThuFriSatSun
LeaveReturnSleep
M10345
Set Program Set Day/Time Start Time Temporary Setting Enrg
Em Heat
Em Ht
3. Press Time ▲ ▲ or Time ▼ ▼ until the current time is
displayed.
NOTE: Tapping the Set Current Day/Time will
change the time in one hour increments.
M10312
Time Set Program
System Fan
Run Program
Hold Temp
Set Current Day/Time
Set Current
Day/Time
Wake Leave Return Sleep
Day Heat/Cool Settings
Daylight Time Copy
Mon
PM
Set Day/Time
2. Press Day until the current day is displayed.
NOTE: Sun=Sunday, Mon=Monday,
Tue=Tuesday, Wed=Wednesday,
Thu=Thursday, Fri=Friday, Sat=Saturday.
M10313
Time Set Program
System Fan
Run Program
Hold Temp
Set Current Day/Time Wake Leave Return Sleep
Day
Day
Heat/Cool Settings
Daylight Time Copy
PM
Tue
Set Day/Time
M10314
Time Set Program
System Fan
Run Program
Hold Temp
Set Current Day/Time Wake Leave Return Sleep
Day
Time
Heat/Cool Settings
Daylight Time Copy
AM
Tue
Set Day/Time
NOTE: If the current time is Daylight Savings
Time, press Daylight Time until DST is
displayed.
M10316
Time Set Program
System Fan
Run Program
Run
Program
Hold Temp
Set Current Day/Time Wake Leave Return Sleep
Day Heat/Cool Settings
Daylight Time Copy
Auto
System Fan
Wake
Room
AM
DST
Tue
Heat
M10315
Time Set Program
System Fan
Run Program
Hold Temp
Set Current Day/Time Wake Leave Return Sleep
Day Heat/Cool Settings
Daylight Time
Daylight
Time
Copy
AM
DST
Tue
Set Day/Time
4. Press Run Program.
INSTALLER SYSTEM-TEST
Use the Installer System-Test to check the thermostat
operation. Refer to Table 4 for a list of the available
system-tests.
To start the system-test:
CAUTION
The minimum off time for compressors is
bypassed during the Installer System-Test.
Equipment damage can occur if the compressor
is cycled too quickly.
Press and hold the increase ▲ and decrease ▼ keys at
the same time until 10 appears. All segments of the
display will be displayed before the 10 appears. See
Fig. 11 and 12.
Table 4. Tests Available In The Installer System-Test.
Fig. 11. Display of all the segments of the LCD.
Fig. 12. Display of test number.
M10257A TEST NUMBER
IMPORTANT
Review the settings to confirm that they match
the system. Press Run Program to exit the
Installer Setup. The thermostat has saved the
Installer Setup changes and initiated a reset in
order to operate using the new settings. Be sure
to set the current day and time immediately.
Setting Current Day and Time
1. Press Set Current Day/Time.
NOTE: On initial power up or after an extended
power loss, 1:00 pm flashes on the
display until a key is pressed.
Test
Number System-Test Description
10-19 Heating equipment can be turned on
and off
20-29 Emergency heat equipment can be turned
on and off
30-39 Cooling equipment can be turned on
and off
40-49 Fan equipment can be turned on and off.
60 0 to
60 19 Keyboard keys test
70-79 Thermostat information including date
code and software versions are displayed