HP Array Controller HSG V8.7 Software Instruction Manuals and User Guides
We have 4 Instruction Manuals and User Guides for Array Controller HSG V8.7 Software HP
Manuals
| Recognized languages: | English |
|---|---|
| Pages: | 206 |
| Size: | 3.86 MB |
Show table of contents
Read manual
Document Outline
- Compaq StorageWorks UltraSCSI RAID Enclosure (DS–BA370 Series)
- Table of Contents
- List of Figures
- List of Tables
- Preface
- Manufacturer’s Declarations
- 1
- 2
- 3
- Environmental Monitoring Unit
- Figure 3–1 EMU
- Product Description
- Configuring the EMU
- Connecting the EMU Communication Bus
- EMU Firmware
- Setting the Temperature Sensors
- Setting the Blower Speed Control
- EMU Status Reporting
- Error Condition Reporting
- Configuration Fault Code Reporting
- Replacing an EMU
- Environmental Monitoring Unit
- 4
- Power Verification and Addressing
- Figure 4–1 PVA
- Figure 4–2 PVA Location
- Product Description
- Functions
- PVA Operation
- Setting the Enclosure Address
- Implementing the Standby Power Mode
- Replacing a PVA
- Power Verification and Addressing
- 5
- Single-Ended I/O Module
- Figure 5–1 Single-Ended I/O Module
- Figure 5–2 I/O Module Location
- Figure 5–3 I/O Module Numbering
- I/O Module and Expansion Cable Error Conditions
- Expanding the UltraSCSI Bus
- Controlling the Internal SCSI Bus
- Controlling the External SCSI Bus
- Controlling the Fault Bus
- Error Reporting
- Rules for Expanding an UltraSCSI Bus
- Cabling an UltraSCSI Subsystem
- Replacing an I/O Module
- Replacing an Expansion Cable
- Single-Ended I/O Module
- 6
- 7
- 8
- Appendix A
- Appendix B
- Assembling an UltraSCSI RAID Subsystem
- Figure B–1 UltraSCSI RAID Subsystem
- Installation Sequence
- Installing the EMU
- Installing the PVA
- Installing the Disk Drive SBBs
- Installing the I/O Modules and Expansion Cables
- Installing Array Controllers and Cache Modules
- Installing the Power System
- Connecting Subsystem Cables
- Configuring the Subsystem
- Assembling an UltraSCSI RAID Subsystem
- Appendix C
- Glossary
| Recognized languages: | English |
|---|---|
| Pages: | 96 |
| Size: | 698 KB |
Show table of contents
Read manual
Document Outline
- Bit PCI-To-Fibre Channel Host Bus Adapter
- Contents
- About This Guide
- Introduction
- Installation
- Device Driver Installation
- Troubleshooting
- Firmware and Diagnostic Utility
- Using LPUTILNT Utility/NT
- Boot BIOS
- Appendix A
| Recognized languages: | English |
|---|---|
| Pages: | 150 |
| Size: | 2.59 MB |
Show table of contents
Read manual
Document Outline
- Contents
- About this Guide
- About SWCC
- Product Overview
- Features
- Components of SWCC
- Client and Agent Versions
- Command Console Client Minimum Hardware and Software Requirements
- Network Specifications
- Connections Supported by SWCC
- Accessing the Storage Window
- Using Command Console
- Setting Up Notification
- Required Components for Notification
- Setting Up Pager Notification
- Using SWCC with a Third-Party Storage Management Program
- Using Event Logging on the Client System to Monitor Your Subsystem
- Interpreting Agent Email Messages
- About Event Information Fields
- Mapping State Change Digits to RAID System Components
- Table 11: State Change Digit Position and Corresponding RAID system Component
- The First Digit of the State Change Field (Overall RAID System)
- The Second Digit of the State Change Field (Disks)
- The Third Digit of the State Change Field (Power Supply)
- The Fourth Digit of the State Change Field (Fans)
- The Fifth Digit of the State Change Field (Battery)
- The Sixth Digit of the State Change Field (Temperature)
- The Seventh Digit of the State Change Field (This_Controller)
- The Eighth Digit of the State Change Field (Communications LUN)
- The Ninth Digit of the State Change Field (Other_Controller)
- The 10th Digit of the State Change Field (External Factors)
- The 11th Digit of the State Change Field (Logical Units)
- Using the Storage Window
- Why Use the Storage Window?
- Configuring a Controller
- Creating Virtual Disks
- Deleting Virtual Disks
- Modifying Virtual Disks
- Configuring the Operating System to Recognize Virtual Disk Changes
- Setting Passwords and Security Options (Network Only)
- Managing and Creating Spare Devices
- Using Configuration Files
- Understanding the Icons
- CLI Window
- Integrating SWCC with Insight Manager
- Troubleshooting
- Troubleshooting Connection Problems
- Invalid Network Port Numbers During Installation
- Network Port Assignments for UNIX-Client/Server Systems
- DHCP and WINS
- Connecting Via the Host SCSI Port
- “Access Denied” Message
- Adding New System by Using Internet Protocol Address May Cause Client to Stop Responding
- “No Agent Running” Message When Adding System to the Navigation Tree
- Troubleshooting the Client
- Authorization Error When Adding an Agent System
- Cannot Open Storage Window
- Client Hangs When LUN Is Deleted
- CLI RUN Commands
- Event Notification for Subsystems Connected to a Client System
- Invalid or Missing Fault Displays and Event Logs
- Pager Notification Continues After Exiting the Command Console Client
- Reconfiguration After Controller Replacement
- Some Graphics Do Not Scale Well with Large Fonts
- Starting Client from the Command Prompt
- Warning Message Windows
- Virtual Disk Recovery from a Configuration File
- Troubleshooting the HS-Series Agents
- Cluster Integration for the HS-Series Agents
- Troubleshooting Connection Problems
- Using the Command Console LUN
- Interpreting SNMP Traps
- Glossary
- Index
| Recognized languages: | English |
|---|---|
| Pages: | 576 |
| Size: | 4.79 MB |
Show table of contents
Read manual
Document Outline
- Figures
- Tables
- Preface
- Precautions
- Conventions
- Required Tools
- Related Publications
- Revision History
- chapter 1
- General Description
- The HSG80 Array Controller Subsystem
- The HSG80 Array Controller
- Cache Module
- External Cache Battery
- chapter 2
- Configuring an HSG80 Array Controller
- Introduction
- Configuring an HSG80 Array Controller
- Setting the PVA Module ID Switch
- Establishing a Local Connection to the Controller
- Selecting a Failover Mode
- Enabling Mirrored Write-Back Cache
- Connecting the Subsystem to the Host
- Connecting a Single Controller to the Host Using One Hub
- Connecting a Dual-Redundant Controller Configuration to the Host
- Figure 2–6 Cabling for Dual-Redundant Configuration with Two Hubs using Fibre Channel Copper Support
- Figure 2–7 Cabling for Dual-Redundant Configuration with Two Hubs using Fibre Channel Optical Sup...
- Figure 2–9 Cabling for Dual-Redundant Configuration with One Hub using Fibre Channel Optical Support
- chapter 3
- Creating Storagesets
- Introduction
- Planning and Configuring Storagesets
- Creating a Storageset and Device Profile
- Determining Storage Requirements
- Choosing a Storageset Type
- Cloning Data for Backup
- Backing Up Your Subsystem Configuration
- Controller and Port Worldwide Names (Node IDs)
- Assigning Unit Numbers for Host Access to Storagesets
- Creating a Storageset Map
- Planning Partitions
- Choosing Switches for Storagesets and Devices
- RAIDset Switches
- Mirrorset Switches
- Device Switches
- Initialize Switches
- Unit Switches
- Configuring Storagesets with CLI Commands
- Adding Disk Drives
- Configuring a Stripeset
- Configuring a Mirrorset
- Configuring a RAIDset
- Configuring a Striped Mirrorset
- Configuring a Single-Disk Unit
- Partitioning a Storageset or Disk Drive
- Adding a Disk Drive to the Spareset
- Removing a Disk Drive from the Spareset
- Enabling Autospare
- Deleting a Storageset
- Changing Switches for a Storageset or Device
- Configuring with the Command Console LUN
- Moving Storagesets
- chapter 4
- Troubleshooting
- Maintenance Features
- Troubleshooting Checklist
- Troubleshooting Table
- Significant Event Reporting
- Using VTDPY to Check for Communication Problems
- Checking for Disk-Drive Problems
- Running the Controller’s Diagnostic Test
- chapter 5
- Replacement Procedures
- Replacing Modules in a Single Controller Configuration
- Replacing Modules in a Dual-Redundant Controller Configuration
- Replacing the External Cache Battery Storage Building Block
- Replacing a GLM
- Replacing a PVA Module
- Replacing an I/O Module
- Replacing DIMMs
- Replacing a Fibre Cable or Hub
- Replacing a PCMCIA Card
- Replacing a Failed Storageset Member
- Shutting Down the Subsystem
- Restarting the Subsystem
- chapter 6
- appendix A
- appendix B
- ADD CONNECTIONS
- ADD DISK
- ADD MIRRORSET
- ADD RAIDSET
- ADD SPARESET
- ADD STRIPESET
- ADD UNIT
- CLEAR_ERRORS CLI
- CLEAR_ERRORS controller INVALID_CACHE
- CLEAR_ERRORS device-name UNKNOWN
- CLEAR_ERRORS unit-number LOST_DATA
- CLEAR_ERRORS unit-number UNWRITEABLE_DATA
- CONFIGURATION RESET
- CONFIGURATION RESTORE
- CONFIGURATION SAVE
- CREATE_PARTITION
- DELETE connections
- DELETE container-name
- DELETE FAILEDSET
- DELETE SPARESET
- DELETE unit-number
- DESTROY_PARTITION
- DIRECTORY
- HELP
- INITIALIZE
- LOCATE
- MIRROR
- POWEROFF
- REDUCE
- RENAME
- RESTART controller
- RETRY_ERRORS UNWRITEABLE_DATA
- RUN
- SELFTEST controller
- SET connection-name
- SET controller
- SET device-name
- SET EMU
- SET FAILEDSET
- SET FAILOVER
- SET mirrorset-name
- SET MULTIBUS_FAILOVER
- SET NOFAILOVER
- SET NOMULTIBUS_FAILOVER
- SET RAIDset-name
- SET unit-number
- SHOW
- SHUTDOWN controller
- UNMIRROR
- appendix C
- appendix D
- Event Reporting: Templates and Codes
- Passthrough Device Reset Event Sense Data Response
- Figure D–1 Pass-through Device Reset Event Sense Data Response Format
- Last Failure Event Sense Data Response
- Multiple-Bus Failover Event Sense Data Response
- Failover Event Sense Data Response
- Nonvolatile Parameter Memory Component Event Sense Data Response
- Backup Battery Failure Event Sense Data Response
- Subsystem Built-In Self Test Failure Event Sense Data Response
- Memory System Failure Event Sense Data Response
- Device Services Non-Transfer Error Event Sense Data Response
- Disk Transfer Error Event Sense Data Response
- Instance Codes
- Last Failure Codes
- Recommended Repair Action Codes
- Component Identifier Codes
- Event Threshold Codes
- ASC/ASCQ Codes
- appendix E