Document Outline

• Contents
• Safety Instructions
  • Important Safety Instructions —SAVE THESE INSTRUCTIONS
• About This Guide
  • Audience
  • Related Documentation
    • MERLIN MAGIX Documentation
    • PortMaster Documentation
  • Additional References
  • Document Conventions
  • Document Advisories
  • Limited Warranty
  • Technical Support
  • INA Module Training Courses
  • PortMaster Training Courses
  • Subscribing to PortMaster Mailing Lists
• INA Module 1
  • INA Module Description
  • INA Administration
    • On the MERLIN MAGIX
    • On the INA Module
  • INA Front Panel
  • Installation and Configuration Steps
• Getting Ready for Configuration 2
  • T1/PRI Provisioning
    • Set Up T1/PRI on the MERLIN MAGIX
    • Assign T1/PRI Channels
  • Network Settings
• Installing the INA Module 3
  • Install the INA Module in a Carrier
  • Connect Cables
    • Connect a Serial Passthrough Cable
    • Set DIP Switches
    • Connect a Console (Optional)
    • Connect a T1/PRI Cable
    • Connect an Ethernet Cable
  • Observe LED Behavior
    • T1/PRI LEDs
    • System LED
    • Ethernet LEDs
• Using the INAWizard 4
  • Install the Wizard
  • Connect the Workstation to the INA Module
    • Over a LAN
    • Using a Crossover Cable
  • Run the Wizard
• Using the Command Line Interface 5
  • Connect a Console
    • Using the C0 Console Port
    • Using a Telnet Session
    • Using the Passthrough Serial Connection
  • Log In
  • Set the Administrative Password
  • Set the Ether0 Network Address
    • Set the IP Address and Netmask
    • Set the Broadcast Address
  • Set the System Name
  • Set the Default Route Gateway
  • Use Name Resolution (Optional)
    • Set Up a Local Host Table
    • Set a Name Service
  • Configure the WAN Port
    • Set the Channel Rate
    • Set Up Additional WAN Ports
    • Set the Port IP Address (Optional)
    • Set the Destination IP Address
    • Set the Netmask
    • Set the Transport Protocol
    • Apply Filters to the WAN Port (Optional)
• Using PMVision 6
  • Install PMVision
  • Connect the Workstation to the INA Module
    • Over a LAN
    • Using a Crossover Cable
  • Run PMVision
  • Communicate with the INA Module
  • Selecting PMVision Functions
    • Using Configuration Functions
    • Enter Basic Settings
    • Set Up Additional WAN Ports
    • Using the Backup and Restore Functions
• Troubleshooting A
  • Observing LED Behavior
  • Observing Boot Messages
  • Using the DS-1 Test Jacks
• Cable Specifications B
  • Cables Specified
  • Console Cable
  • T1/PRI Cable
  • Ethernet Interface
  • Crossover Cable
• MERLIN MAGIX Administration C
  • INA Module System Programming Summary
  • INA Module Administration Options
    • Activate or Deactivate the Onboard CSU
    • DSU Channel Selection
  • INA Module Maintenance Options
    • Error Events
    • 24 Hour Event Totals
    • Current Events
    • Selected Interval Events
    • Clearing Error Events
    • Demand Tests
  • INA Module System Interactions
    • Backup and Restore
    • Surrogate Operation
    • Board Renumbering
    • Print Reports
    • PCMCIA Flash Memory Card-Based Upgrade Operation
    • Other System Interactions
• Index
  • Numerics
  • A
  • B
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • L
  • M
  • N
  • O
  • P
  • R
  • S
  • T
  • U
  • V
  • W