Document Outline

• Summit 3000
  • Low-Profile Floor Scale
• Installation Manual
  • Contents
    • 1.0 Introduction and System Overview 1
      • 1.1 Operating Requirements 1
    • 2.0 Installation 2
      • 2.1 Overview 2
      • 2.2 Site Preparation 2
      • 2.3 Unpacking 2
      • 2.4 Assembly 3
        • 2.4.1 Installing and adjusting feet 3
        • 2.4.2 Anchor Plate Installation 3
      • 2.5 Electrical Interface to Indicator 4
      • 2.6 Pit Installation 5
      • 2.7 Access Ramps 6
    • 3.0 Adjustments and Calibration 7
      • 3.1 Mechanical Adjustments 7
      • 3.2 Corner Correction 7
      • 3.3 Calibration Procedure 8
    • 4.0 Service Information 9
      • 4.1 Troubleshooting Guide 9
      • 4.2 Periodic Maintenance 9
      • 4.3 Load Cell Replacement 10
        • 4.3.1 Load Cell Wiring to Junction Box 11
  • Summit 3000 Limited Warranty 12
• 1.0 Introduction and System Overview
  • Figure 1-1. The Summit 3000 Floor Scale
  • 1.1 Safety
    • Safety Signal Definitions:
  • 1.2 Operating Requirements
    • Electrical Grounding
    • Load Cell Excitation
    • Grade Level Requirements
    • Safe Static Overloading Capacity
    • Nominal Scale Height
    • Approvals
• 2.0 Installation
  • 2.1 Overview
    • 1. Select a site
    • 2. Check levelness and smoothness of site
    • 3. Unpack the floor scale
    • 4. Adjust the four feet on the scale
    • 5. Install mounting plates to the floor (optional)
    • 6. Connect cable to the indicator
    • 7. Calibrate the unit
  • 2.2 Site Preparation
  • 2.3 Unpacking
    • Figure 2-1. Proper Lifting Technique
  • 2.4 Assembly
    • 2.4.1 Installing and adjusting feet
    • 2.4.2 Anchor Plate Installation
      • Figure 2-2. Anchor Plate Installation
  • 2.5 Electrical Interface to Indicator
    • 1. Remove the four screws using an allen wrench.
    • 2. Slide the junction box assembly out of the deck.
    • 3. Open and remove the top of junction box.
    • 4. Push the cable end into the junction box through a cord grip.
    • 5. Connect the wires to the indicator terminal (Figure 2-3) as shown in Table 2-1.
    • 6. Pull out excess and tighten the cord grip to hold the cable snugly.
    • Table 2-1. Junction Box Connections
      • Figure 2-3. Junction Box Wiring Diagram
      • 7. The cable must be routed to the indicator in a manner that will protect the cable from damage. This method of cable protection in non-washdown applications are shown in Figure 2-4. When planning cable routing, leave a loose coil of excess cable un...
        • Figure 2-4. Load Cell Protection
      • 8. When the interface cable is protected and in its final position, complete connections to the indicator. See the indicator installation manual for wiring information.
      • 9. If necessary, trim corners as described in Section 3.2.
      • 10. Check all strain relief fittings for tightness.
      • 11. Put the cover back onto the junction box assembly and place the junction box back into the floor scale cutout.
      • 12. Secure the Summit 3000 floor plate.
  • 2.6 Pit Installation
    • Figure 2-5. Pit Frame Diagram
    • Site Considerations
      • Figure 2-6. Section Showing Installed Summit 3000 and Pit Frame
  • 2.7 Access Ramps
    • Figure 2-7. Optional Access Ramp
• 3.0 Adjustments and Calibration
  • 3.1 Mechanical Adjustments
  • 3.2 Corner Correction
    • Figure 3-1. Summing Board Diagram
  • 3.3 Calibration Procedure
• 4.0 Service Information
  • 4.1 Troubleshooting Guide
    • Table 4-1. Troubleshooting Table
  • 4.2 Periodic Maintenance
  • 4.3 Load Cell Replacement
    • Table 4-2. Load Cell Replacement Numbers
      • Figure 4-1. Load Cell Assembly
      • Figure 4-2. Bottom View of Scale
      • Figure 4-3. Foot Pad - Side View
    • 4.3.1 Load Cell Wiring to Junction Box
      • Figure 4-4. Corner Numbering - Top View
      • Table 4-3. Load Cell Wiring
  • Summit 3000 Limited Warranty