Document Outline

• Contents
  • 1 Mounting 5
  • 2 Electrical connections 7
    • 2.1 Connecting diagram 7
    • 2.2 Connecting diagram for the options card 8
    • 2.3 Terminal connection 8
  • 3 Operation 12
    • 3.1 Front view 12
    • 3.2 Behaviour after power-on 13
    • 3.3 Operating level 13
    • 3.4 Maintenance manager / Error list 14
    • 3.5 Self-tuning 16
      • 3.5.1 Preparation before self-tuning 16
      • 3.5.2 Self-tuning start 17
      • 3.5.3 Self-tuning cancellation 17
      • 3.5.4 Acknowledgement of failed self-tuning 17
      • 3.5.5 Optimization after start-up or at the set-point 17
      • 3.5.6 Selecting the method ( ConF/ Cntr/ tunE) 18
      • 3.5.7 Optimization at the set-point for 3-point stepping controller 21
      • 3.5.8 Examples for self-tuning attempts 22
    • 3.6 Manual tuning 23
    • 3.7 Second PID parameter set 24
    • 3.8 Alarm handling 25
    • 3.9 Operating structure 27
  • 4 Configuration level 28
    • 4.1 Configuration survey 28
    • 4.2 Configurations 29
    • 4.3 Set-point processing 38
      • 4.3.1 Set-point gradient / ramp 38
    • 4.4 KS50-1 cooling functions 38
      • 4.4.1 Standard ( CyCl= 0 ) 38
      • 4.4.2 Switching attitude linear ( CyCl= 1 ) 39
      • 4.4.3 Switching attitude non-linear ( CyCl= 2 ) 39
      • 4.4.4 Heating and cooling with constant period ( CyCl= 3 ) 40
    • 4.5 Configuration examples 41
      • 4.5.1 On-Off controller / Signaller (inverse) 41
      • 4.5.2 2-point and continuous controller (inverse) 42
      • 4.5.3 3-point and continuous controller 43
      • 4.5.4 3-point stepping controller (relay & relay) 44
      • 4.5.5 D - Y - Off controller / 2-point controller with pre-contact 45
      • 4.5.6 KS50-1 with measured value output 46
  • 5 Parameter setting level 48
    • 5.1 Parameter survey 48
    • 5.2 Parameters 49
    • 5.3 Input scaling 52
      • 5.3.1 Input Inp.1 52
      • 5.3.2 Input InP.2 52
  • 6 Calibration level 53
  • 7 Programmer 56
  • 8 Special functions 57
    • 8.1 Start-up circuit 57
    • 8.2 Boost function 58
    • 8.3 KS50/52-1 as Modbus master 59
    • 8.4 Linearization 60
  • 9 BlueControl 61
  • 10 Versions 62
  • 11 Technical data 64
  • 12 Safety hints 67
    • 12.1 Reset to default 69
• Index
  • 0-9
    • 2-point correction 55
  • A
    • Accessories 62
    • Alarm handling 25 - 26
  • B
    • BlueControl 61
    • Boost function 58
    • Bus interface
      • Technical Data 65
  • C
    • Calibration level (CAL) 53 - 55
    • Certifications 66
    • Configuration examples
      • 2-point controller 42 - 43
      • 3-point stepping controller 44
      • D - Y -Off controller 45
      • Measured value output 46
      • Signaller 41
    • Configuration level
      • Configuration parameters 29 - 37
      • Parameter survey 28
    • Connecting diagram 7
    • Connecting examples
      • di2/3, 2-wire transmitter supply 10
      • INP2 current transformer 9
      • OUT1/2 heating/cooling 9
      • OUT3 as logic output 10
      • OUT3 transmitter supply 10
      • RS485 interface 11
    • Control inputs di1, di2, di3
      • Technical data 64
    • Cooling functions
      • Constant period 40
      • Standard 38
      • Water cooling linear 39
      • Water cooling non-linear 39
    • Current signal measuring range 64
  • • Digital inputs di1, di2, di3
      • Configuration 34
      • Technical data 64
  • E
    • Environmental conditions 65
    • Equipment 63
    • Error list 14
    • Error status 15
  • F
    • F - key 12
    • Front view 12
  • I
    • Input INP1
      • Configuration 30
      • Parameters 51
      • Technical data 64
    • Input INP2
      • Configuration 31
      • Parameters 51
      • Technical data 64
    • Input scaling 52
  • L
    • LED
      • Ada - LED 12
      • Err - LED 12
      • ì - LED 12
      • LED colours 12
      • ò - LED 12
      • run - LED 12
      • SP.x - LED 12
    • Linearization 60
  • M
    • Maintenance manager 14 - 15
    • Manual tuning 23
    • Modbus master 59
    • Mounting 5 - 6
  • • Offset correction 54
    • Optimization at the setpoint 19
    • Output OUT1
      • Configuration 32
      • Technical data 65
    • Output OUT2
      • Configuration 32
      • Technical data 65
    • Output OUT3
      • Configuration 32
      • Technical data 65
    • Output OUT5
      • Configuration 33
      • Technical data 65
    • Output OUT6
      • Configuration 33
      • Technical data 65
  • P
    • Parameter setting level
      • Parameter survey 48
      • Parameters 49 - 51
    • Power supply 65
    • Programmer
      • Changing segment end setpoint 56
      • Changing segment time 56
      • Parameter setting 56
      • Set-up 56
      • Starting/Stopping 56
  • R
    • Reset to default 69
    • Resistance thermometer measuring range 64
  • S
    • Safety hints 67 - 69
    • Safety switch 5
    • Safety test 66
    • Self tuning
      • Cancellation 17
      • Causes of cancellation 17
      • Self-tuning cancellation 17
    • Start-up circuit 57
  • T
    • Thermocouple measuring range 64
  • V
    • Versions 62 - 63
    • Voltage signal measuring range 64