Integra RDV-1.1 - Manual (Page 67)

67
Advanced Playback —Continued
You can turn off all of the output video circuitry, elimi-
nating the possibility of interference, for a pure-audio
experience when playing audio-only discs.
Notes:
• When the video circuitry is turned off, all of the
RDV-1.1’s video outputs don’t work. The HDMI IN
and VIDEO IN inputs are not affected.
• With some discs you need start playback from a menu,
in which case you should turn off the video circuitry
after starting playback.
• Although intended for use with audio discs, this func-
tion can also be used to enjoy soundtracks and music
on DVD-Video discs and VCDs.
This section explains how to select the video input
source when you’ve connected other video components
to the RDV-1.1’s video inputs, as shown on page 39.
Notes:
• See the table on page 27 for details on how the
RDV-1.1’s video outputs work with each video input
source.
This section explains how to change the video resolution
when your TV or projector is connected to the HDMI
OUT.
Notes:
• With HDMI, the TV reports to the RDV-1.1 what res-
olutions it supports, and then only those resolutions
can be selected.
• The letters i and p indicate interlaced and progressive
respectively .
Turning Off the Video Circuits
1 Press the remote controller’s
[Video Off] button or the
RDV-1.1’s [Video Circuit Off] but-
ton.
The output video circuitry is turned off,
the Video Circuit Off indicator lights
up, and the V.OFF indicator appears on
the display.
2 To turn the video circuitry back
on, press the button again.
The output video circuitry is turned on,
the Video Circuit Off indicator goes off,
and the V.OFF indicator disappears
from the display.
+10 0 Clear
1 2 3
4 5 6
7 8 9
Input I
+
-
Enter
Set up Retu rn
L 4
L 2 L1 V Off V In
Aspect A-B Repeat
Rsltn Angle Subtitle Audio
L 3
To p M enu Men u
VOL
+
-
V3
TV
Input D M S
DVD Amp VCR
DVD V1 V 2
LM RD
Zoom CH
L Mode
Learning
Search Memory Dimmer Amp Input
Display
Audio
Sel
Zoom On Picture Control
Random Step/Slow
Muting
Angle Subtitle Audio
Aspect A-B Repeat
On Standby T V
T V CH
T V VOL
RC-561DV
Last Memory
Resolution
Mode
Amp Input
Rec
Open/Close
Video Input Video Off
Video Off
Resolution
Video Input
Video Input knob & indicators
Video Circuit Off
Off indicator
V Off
Video Off
Remote controller
Selecting the Video Input Source
Turn the Video Input knob to
select the video input source.
DVD: The RDV-1.1.
External: VIDEO IN (COMPONENT,
S VIDEO, or VIDEO).
HDMI: HDMI IN.
The DVD, External, and HDMI indica-
tors show the currently selected video
input source.
Setting the HDMI Output Resolution
Press the remote controller’s
[Resolution] button.
The current resolution scrolls across
the display.
While the resolution is scrolling,
press the [Resolution] button
repeatedly to select another res-
olution.
The RDV-1.1 supports the following
resolutions:
640 x 480p: (VGA), 60 Hz
720 x 480p: (progressive), 60 Hz
720 x 576p: (progressive), 50 Hz
1280 x 720p: (progressive), 50/60 Hz
1920 x 1080i: (interlaced ), 50/60 Hz
Through Source Resolution: External
input video is output at the same resolu-
tion. DVD playback is output at 480p or
576p.
V In
Video Input
Remote controller
Rsltn
Resolution
Remote controller