Integra DTR-7 - Manual (Page 13)

13
Connecting the power
Connecting the power
• Before you turn on the receiver, confirm that all connections
have been made properly.
• Turning on this receiver’s power may cause a momentary power
surge, which might interfere with other electrical equipment,
such as computers. If this happens, use a wall outlet on a differ-
ent circuit.
1. Press the POWER switch to set the receiver to Standby
mode.
The STANDBY indicator will light up.
2. Press the STANDBY/ON button to turn on the receiver. The
display will light up and the STANDBY indicator will be
turned off.
If you press the STANDBY/ON button, the receiver returns to
Standby mode.
Turning the power on from the remote controller:
1. Press the MODE AUDIO button.
2. Press the POWER ON button to turn on the power to the
receiver, or press the POWER STNBY button to set the re-
ceiver in standby mode.
• You cannot use the remote controller if the POWER switch on
the receiver is set to OFF.
• Set the volume level to minimum before you turn off the power
to the receiver.
Connecting an equalizer
(DTR-7)
The AMP IN and the PRE OUT FRONT connectors are attached
with jumper plugs. When connecting an equalizer, remove these
jumper plugs before connecting the audio connection cables.
1. Remove the jumper plugs.
See “Connecting power amplifiers.”
2. Connect an equalizer.
DTR-7
Input jack
R V L R L
R L
R L
VIDEO-1
OUT
IN
VIDEO-2
VIDEO-3
OUT
IN
IN
TAPE
VIDEO
S VIDEO
OSD SELECTOR
(REC) OUT
IN (PLAY)
DIGITAL OUTPUT
DIGITAL INPUT
COAXIAL 1
COAXIAL 2
OPTICAL 1
OPTICAL 2
OPTICAL
FRONT
FRONT
CENTER
SUB WOOFER
SURROUND
FRONT
CENTER
CD
PHONO
SUB WOOFER
SURROUND
AMP IN
PRE OUT
GND
MONITOR OUT
S
REMOTE CONTROL REMOTE LOCAL
IN DVD
L R L R
L R
SURROUND SPEAKERS FRONT SPEAKERS A
CENTER SPEAKER
FRONT SPEAKERS B
MULTI CHANNEL
INPUT
MULTI SOURCE OUT
R L
AV RECEIVER
CAUTION: SPEAKER IMPEDANCE 6 OHMS MIN. / SPEAKER
ANTENNA
AM
FM 75
AC INLET
AC OUTLETS AC 120V 60Hz SWITCHED TOTAL 120W 1A MAX. MODEL NO. DTR-7
R L
FRONT
FRONT
AMP IN
PRE OUT
Output jack
Input jack
2. POWER ON
button
2. POWER STNBY
button
1. MODE AUDIO
button
MASTER VOLUME
STANDBY/ON
PHONES
VIDEO S VIDEO
POWER
OFF ON
A SPEAKERS B
FM AM PHONO C D TAPE VIDEO-1 DVD VIDEO-4 VIDEO-3 VIDEO-2
D O W N U P
FM MUTE/ MODE CHARACTER/ MEMORY SP/SYS
SETUP
MODE
AUDIO ADJUSTMENT BASS/ TREBLE
DISPLAY DSP
PRESET/MODE ADJ
PUSH TO ENTER
DOWN TUNING UP
THX /DTS
SURROUND MODE
LISTENING MODE STEREO DIRECT DIGITAL/
ANALOG CH LEVEL
DIMMER
REC OUT / MULTI SOURCE
TI CH MUL INPUT
ANDBY ST TI SOURCE MUL
DTR - 7 by
VIDEO4 (MONO)
AUDIO L R
2. STANDBY/ON button
STANDBY indicator
Display
1 POWER switch
R V L R L
R L
R L
VIDEO-1
OUT
IN
VIDEO-2
VIDEO-3
OUT
IN
IN
TAPE
VIDEO S VIDEO
OSD SELECTOR
(REC) OUT
IN (PLAY)
DIGITAL OUTPUT
DIGITAL INPUT
COAXIAL 1
COAXIAL 2
OPTICAL 1
OPTICAL 2
OPTICAL
FRONT
FRONT
CENTER
SUB WOOFER
SURROUND
FRONT
CENTER
CD
PHONO
SUB WOOFER
SURROUND
AMP IN
PRE OUT
GND
MONITOR OUT
S
REMOTE
CONTROL REMOTE LOCAL
IN DVD
L R L R
L R
SURROUND SPEAKERS FRONT SPEAKERS A
CENTER SPEAKER
FRONT SPEAKERS B
MULTI CHANNEL
INPUT
MULTI SOURCE OUT
R L
AV RECEIVER
CAUTION: SPEAKER IMPEDANCE 6 OHMS MIN. / SPEAKER
ANTENNA
AM
FM 75
AC INLET
AC OUTLETS AC 120V 60Hz SWITCHED TOTAL 120W 1A MAX. MODEL NO. DTR-7
2
1
Connecting a power cable
1. Connect the outlet plug on the included power cable to the
AC INLET on the DTR-7/ DTR-6.
2. Plug-in the other end of the cable to a wall AC outlet.
Notes:
• Do not use any power cable other than the included cable. The included
cable is designed for use only with the DTR-7/ DTR-6. Do not use it for
any other device.
• Do not connect or disconnect the outlet plug from the DTR-7/DTR-6
while the other end is plugged into the wall AC outlet.
Epualizer