JVC KD-AV7000 - Manual (Page 345)

1
KD-AV7008
Installation/Connection Manual
LVT1174-002A
[A]
This unit is designed to operate only on 12 V DC, NEGATIVE ground electrical systems. If your
vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC
car audio dealers.
WARNINGS
• DO NOT install any unit in locations where;
– it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic
accident.
– it may obstruct the operation of safety devices such as air bags, as this may result in a fatal
accident.
– it may obstruct visibility.
• DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic
accident.
• The driver must not watch the monitor while driving.
If the driver watches the monitor while driving, it may lead to carelessness and cause an accident.
• If you need to operate the main unit while driving, be sure to look ahead carefully or you may be
involved in a traffic accident.
• If the parking brake is not engaged, “DRIVER MUST NOT WATCH THE MONITOR WHILE
DRIVING.” appears on the monitor, and no playback picture will be shown.
– This warning appears only when the parking brake wire is connected to the parking brake
system built in the car.
Notes on mounting the hideaway unit
• Mount on a firm surface, under the front seat or in the trunk.
• Since heat is generated inside the unit, do not mount near inflammable objects. In addition, mount
in an area that will not prevent the unit from dissipating heat.
• Do not mount the unit in the places which are subject to heat such as near a radiator, in a glove
compartment or in insulated area such as under a car mat that will prevent the unit from dissipating
heat.
Notes on electrical connections
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC
car audio dealer.
• Maximum input of the speakers should be more than 50 W at the rear, 50 W at the front, and
35 W at the center, with an impedance of 4 Ω to 8 Ω.
• Be sure to ground each unit to the car’s chassis.
• The main unit and the hideaway unit become very hot after use. Be careful not to get burned
when removing them.
• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.
• Take preventative measures to avoid unexpected disconnection of the cords and
damage to the cords. This trouble may happen while moving or reclining the seat.
1004MNMMDWJEIN
EN
Parts list
a Main unit
r Washer—ø5 s Rubber cushion
q Lock nut—M5
b Hideaway unit
t Remote controller u Battery
CR2025
RM-RK220
v Center speaker/rear
camera cord
w Extension antenna cord
C Sleeve-mounting plates
Type A Type B
d Fixing screws—
M5 x 6 mm
e, f Power cords
e For main unit: f For hideaway unit:
g AV bus cable—2.5 m
h Crimp connectors i Handles j Soft case k Trim plate
l Sleeve m Brackets n Fixing screws—
M4 x 8 mm
o Blind cover
p Mounting bolt—
M5 x 20 mm
When installing the unit without using the sleeve
In a Toyota for example, first remove the car radio and install the unit in its place.
Note : When installing the unit on the mounting bracket, make sure to use screws of proper
length refering to the table above. If longer screws are used, they could damage the unit.
Flat type screws* 2
Bracket* 2
* 2 Not included with this unit.
Pocket
1 2 3 4 5
6 7 8 9
l
r q
p
When using the optional stay
Screw (option)
Stay (option)
Fire wall
Dashboard
Install the unit at an angle of less than 30˚, taking it into account
that the monitor would eject when in use (see below).
30˚
Required space for the monitor ejection
60˚
105˚
51.8
143.3
15
12.2 mm
177
© 2004 Victor Company of Japan, Limited
Use the following screws
For No.1 – 5 M5 x 8 mm* 2
For No.6 – 9 M4 x 3 mm* 2
InstallKD-AV7008_1[A]5.p65 04.10.5, 3:49 PM 1