8 staying within range, 9 microphone noise blackout, 10 narrowband vs. wideband audio – Jabra GO 6470 User Manual

Page 46: 11 high capacity jabra go installations, En g li sh

Advertising
background image

46

en

g

li

sh

Jabra GO 6470 User manUal

7.8 Staying within Range

the Jabra GO headset supports the following maximum ranges:

- when talking through the Jabra GO Base or Jabra lInK 350 UsB Bluetooth® adapter:

up to 100m

- when talking over Bluetooth® wireless technology Class 2 (most) mobile phones:

up to 25m

In practice, you will probably find the range to be somewhat shorter due to physical obstructions and

electromagnetic interference. also, if your headset is in power save mode, the range is slightly reduced.
the sound in your headset will slowly deteriorate as you move farther from its Bluetooth® wireless technology

partner; move back into range to restore sound quality. all sound will stop if you move all the way out of range.
If you are talking through the Jabra GO Base or Jabra lInK 350 UsB Bluetooth® adapter, then your call will be kept

open for up to 120 seconds after you go out of range and then disconnected. If you are talking trough a mobile

phone, then you call will probably be disconnected the moment you walk out of range.
after moving out of range, the headset will try to reconnect to the lost device periodically — the headset will try

to reconnect every 15 secs up to five times and then every 15 minutes for 5 hours. after that, it gives up to save

power.
similarly, the Jabra GO base will periodically try to reconnect to a paired headset that went out of range, but it

will increase the frequency of reconnection attempts. this avoids interfering with other Bluetooth devices.
you can manually force the headset to attempt reconnection at any time by tapping on the multifunction button

while the lost device is the target (either the mobile phone or base).
Usually, when you turn off a connected Bluetooth® wireless technology device while the headset is turned on,

the headset will react in the same way as if you had simply walked out of range, as described above.

Tip: for optimal performance with a Bluetooth® wireless technology Class 2 mobile phone, wear the

headset and your mobile phone on the same side of your body or within line of sight. In general, you will

get better performance when there are no obstructions between your headset and your mobile phone.

7.9 MicRoPhone noiSe Blackout™

the Jabra GO headset features an advanced, two-microphone noise Blackout™ system that will help ensure that

your voice will be clear and easy to understand — even when you are sitting in a crowded office or other noisy

environment. It works by using a pair of directional microphones: one facing towards your mouth and one facing

away. these two signals are combined inside the headset, which subtracts the room-noise signal from the voice

signal, leaving only your voice behind when it is sent to your phone.
this system works best when the headset’s microphone is placed as close as possible to your mouth.

7.10 naRRowBand vS. wideBand audio

the Jabra GO headset supports both wideband and narrowband audio, but uses narrowband by default. In

particular, you should consider using wideband if you listen to music from your pC.

Notes:

- wideband audio is only supported between Jabra GO headset and base for softphones or for streaming

music from a pC.

- wideband audio may slightly reduce the range of your headset

see the section “Settings menu” for more.

7.11 high caPacity Jabra go inStallationS

Bluetooth® wireless technology uses low-power radio technology for wireless transmission. all radio technologies

are subject to interference from other products using radio technologies commonly used in offices.
therefore, under certain conditions, you might experience some performance degradation if you install many

Jabra GO headsets in one location or if there is interference from other radio technologies. for Bluetooth®

wireless technology, those performance degradations are typically the result of interference from other

Bluetooth® wireless technology products including Jabra GO products and from wifi networks. performance

issues manifest themselves as audible clicks and pops but will very seldom prevent headset operation.

Advertising