Sanyo DVW-7100a - Manual (Page 9)

2 2
1 1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see“RF Output Channel” section.
Preset for Use
– 9 – EN
Setup
VCR VCR DVD DVD
OUTPUT
POWER POWER
VIDEO VIDEO AUDIO AUDIO AV INP AV INPUT REW REW F.FWD STOP STOP/EJECT JECT PLAY REC REC TIMER REC TIMER REC REC REC/OTR OTR CHANNEL CHANNEL
OPEN OPEN/CLOSE CLOSE
VCR VCR DVD DVD PROGRESSIVE PROGRESSIVE OUTPUT OUTPUT SKIP SKIP/REV REV STOP STOP PLAY PLAY FWD WD/SKIP SKIP
OUTPUT button
DVD OUTPUT
light
VCR OUTPUT
light
DVD
button
VCR
button
STOP
PLAY
1 2 3
4 5 6
7 8 9
0 +10
POWER SPEED AUDIO
DISPLAY
SLOW
PAUSE
ENTER
MENU
TOP MENU SETUP
MODE V.SURR SEARCH MODE
A-B REPEAT ANGLE SUBTITLE
T-SET
DVD
REC OTR
VCR TV
SKIP CH.
CLEAR C.RESET
VCR
RETURN
Pressing the OUTPUT button on the front panel
switches the output signal. (The VCR or DVD
OUTPUT light is lit.)
However, when using the remote control, you
must press the DVD or VCR button on the
remote control first.
• To use the VCR, press the VCR button on the
remote control.
(Verify that the VCR OUTPUT light is lit.)
• To use the DVD player, press the DVD button
on the remote control.
(Verify that the DVD OUTPUT light is lit.)
Note
• This remote control cannot operate your TV.
POWER POWER
VIDEO VIDEO AUDIO AUDIO
AV INP V INPUT REW REW F.FWD STOP STOP/EJECT JECT PLAY
REC REC TIMER REC TIMER REC
REC REC/OTR OTR CHANNEL CHANNEL
OPEN OPEN/CLOSE CLOSE
VCR VCR DVD DVD PROGRESSIVE PROGRESSIVE
OUTPUT OUTPUT SKIP SKIP/REV REV STOP STOP PLA PLAY FWD WD/SKIP SKIP
VCR/DVD Switching
Front Panel Display
Lights up when
the inserted disc
is being played
back.
Flashes when an
unacceptable disc
is installed.
Lights up when the timer recording
or an OTR recording has been set.
Lights up during a recording.
Flashes when a recording is paused.
Lights up when the progressive scan
system is activated.
Need help? Call
1-800-813-3435
Lights up when power is on.
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
Hint Hint
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
POWER
3 3
CH 01
AUTO SET UP
No No Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
• You can select only the channels memo-
rized in this unit by using the CHANNEL
buttons.
• If "AUTO SET UP" appears on the TV
screen again, check the cable connections.
Then, press the
B button once again.
Y Y es es Press the MENU
button to exit.
• Refer to “Hint for Cable Box
or Satellite Box” section on
page 6.
Do you connect the cable from the cable box or
the satellite box to the DVD+VCR’s ANT-IN jack?
YES
NO
Turn on the unit for the first
time
TV Screen Remote Control
VCR VCR VCR
VCR
Press the VCR button first.
or
TIP:
If you change the on-screen language at
step [2], change the language for DVD func-
tion in “PLAYER MENU” setting. (Refer to
page 20.)
H9680UD_EN/SP.qx3 04.8.10 4:26 PM Page 9