Sony PDW-1500 - Manual (Page 58)

Ch
apt
er 6
Men
u
s
58
6-2 Basic Setup Menu
1
Press the MENU button.
The menu appears in the time data display.
2
Press the RESET button.
A message “Init setup?” appears in the time data
display.
To abandon operations and return to the setup
menu display
Press the RESET button again.
3
Press the SET button.
The menu settings are reset to their factory default
settings.
Switching between 525(U)-line, 525(J)-line
and 625-line modes (menu item 013)
To switch between 525(U)-line, 525(J)-line and 625-line
operation modes, do as follows.
1
Press the MENU button.
2
Turn the jog dial or shuttle dial to display menu item
013 in the time data display.
3
Hold down the SHUTTLE button, and turn the jog dial
or shuttle dial to set menu item 013 to “on.”
4
Press the SET button.
5
Hold down the SHUTTLE button, and turn the jog dial
or shuttle dial to select the line mode 525(U), 525(J) or
625.
6
Press the SET button.
7
Turn the unit off (press the on/standby switch to put
the unit in the standby state).
Next time the unit is turned on (when the unit is put in the
operating state by pressing the on/standby switch), it
operates in the new mode.
Menu bank operations (menu items B01 to
B13)
This unit allows menu settings to be saved in what are
termed “menu banks.” Saved sets of menu settings can be
recalled for use as required.
To jump to menu item B01
You can recall any required menu by turning the jog dial
or shuttle dial after pressing the MENU button.
If you press the MENU button first, then the COUNTER
SELECT button, you can jump directly to menu item B01
or H01. The recalled menu item toggles between B01 and
H01 every time you press the COUNTER SELECT button.
Saving the current active menu settings
Set one of menu items B11 “SAVE BANK 1” to B13
“SAVE BANK 3” to “on,” depending on which of the
menu banks you wish to save in, then press the SET button.
Recalling settings from a menu bank
Set one of menu items B01 “RECALL BNK 1” to B03
“RECALL BNK 3” to “on,” depending on which of the
menu banks you wish to recall from, then press the SET
button.
The current active setup menu settings as well as settings
saved in menu banks are stored in separate storage areas
(three areas) for 525(U)-line, 525(J)-line and 625-line
modes.
REC
VARIABLE
PRESET
PB
L MIX
R
MONITOR
NETWORK
LOCAL REMOTE
ACCESS
PHONES
TOP F REV F FWD END
PREV NEXT PLAY
AUDIO MONITOR SEL METER SEL INPUT CH INPUT SEL VIDEO INPUT SEL COUNTER SELECT
SUB CLIP THUMB NAIL SET RESET
SHIFT
EJECT
HOLD
STOP REC
SH UTT LE JOG VAR
MARK1 ESSENCE MARK S.SEL
MARK2
IN OUT
ALL/CH-1 CH-2 CH-3 CH-4
OVER dB
-12 -20
-30 -40
-60
0
CH- 15
BQ DATA
ANA SDI
AE8/EBU
OVER dB
-12 -20
-30 -40
-60
0
CH- 26
BQ DATA
ANA SDI
AE8/EBU
OVER dB
-12 -20
-30 -40
-60
0
CH- 37
BQ DATA
ANA SDI
AE8/EBU
OVER dB
-12 -20
-30 -40
-60
0
CH- 48
BQ DATA
ANA SDI
HOURS MINUTES SECONDS FRAMES
AE8/EBU VITC VITC COUNTER REC INH VIUB
EDIT KEY INH REMOTE [9P iLINK] INPUT i.LINK
SDI
1/2 5/6 3/4 7/8 625 525 IMX[50 40 30] DVCAM 4 8 CH 18 24 BIT
CMPST
Y-R,B
SG
ALARM
MONITOR AUDIO
SYS MENU MENU
1 2
3
Current active
menu settings
Menu bank 1
Menu bank 2
Menu bank 3
Recall
Save
Recall
Save
Recall
Save