Sanyo PDG-DHT8000L - Manual (Page 83)

8
Appendix
ON-SCREEN
DISPLAy
RESOLUTION H-Freq .(kHz) V-Freq .(Hz)
1080p
1920x1080 33.750 30.000
1920x1080 28.125 25.000
1920x1080 27.000 24.000
1920x1080 67.500 60.000
1920x1080 56.250 50.000
1080psf/30 1920x1080 33.750 60.000
1080psf/25 1920x1080 28.125 50.000
1080psf/24 1920x1080 27.000 48.000
When an input signal is digital from the DVI or HDMI terminal, refer to the chart below.
ON-SCREEN
DISPLAy
RESOLUTION H-Freq .(kHz) V-Freq .(Hz)
D-VGA 640x480 31.470 59.940
D-480p 720x480 31.470 59.880
D-575p 720x575 31.250 50.000
D-SVGA 800x600 37.879 60.320
D-XGA 1024x768 43.363 60.000
D-WXGA 1 1366x768 48.360 60.000
D-WXGA 2 1360x768 47.700 60.000
D-WXGA 3 1376x768 48.360 60.000
D-WXGA 4 1360x768 56.160 72.000
D-WXGA 5 1366x768 46.500 50.000
D-WXGA 6 1280x768 47.776 59.870
D-WXGA 7 1280x768 60.289 74.893
D-WXGA 8 1280x768 68.633 84.837
D-WXGA 9 1280x800 49.600 60.050
D-WXGA 10 1280x800 41.200 50.000
D-WXGA 11 1280x800 49.702 59.810
D-WXGA 12 1280x800 63.980 60.020
D-SXGA 1 1280x1024 63.980 60.020
D-SXGA 2 1280x1024 60.276 58.069
D-SXGA+ 1 1400x1050 63.970 60.190
D-SXGA+ 2 1400x1050 65.350 60.120
D-SXGA+ 3 1400x1050 65.120 59.900
D-SXGA+ 6 1400x1050 64.744 59.948
D-SXGA+ 7 1400x1050 65.317 59.978
D-WUXGA 2 1920x1200 74.038 59.950
D-WSXGA+ 1 1680x1050 65.290 59.954
D-WXGA+ 1 1440x900 55.935 59.887
ON-SCREEN
DISPLAy
RESOLUTION H-Freq .(kHz) V-Freq .(Hz)
D-720p 1280x720 45.000 60.000
D-720p 1280x720 37.500 50.000
D-1035i
1920x1035
(Interlace)
33.750 60.000
D-1080i
1920x1080
(Interlace)
33.750 60.000
1920x1080
(Interlace)
28.125 50.000
D-1080psf/30 1920x1080 33.750 60.000
D-1080psf/25 1920x1080 28.125 50.000
D-1080psf/24 1920x1080 27.000 48.000
D-1080p
1920x1080 33.750 30.000
1920x1080 28.125 25.000
1920x1080 27.000 24.000
1920x1080 67.500 60.000
1920x1080 56.250 50.000
✔ Note:
• Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.
• Specifications are subject to change without notice.
• You might be able to project images even when signals other than above are inputted, however the functions of the
projector could be limited.
• Depending on your PC settings, the digital signals of your PC may not be projected correctly. In such a case, confirm
your PC settings.
• When you project a DVI signal, connect the cables, turn the projector on, then select the input. Finally, turn on your PC.
Be sure to follow this procedure, otherwise an image may not be projected on the screen. If an image is not projected
correctly, restart your PC.
• Do not disconnect the cable while the projector is running. If the cable has been disconnected and then reconnected, an
image may not be correctly projected.