Reading command tables, Computer control command tables, 75 appendix – Kenwood TS-570S TS-570D User Manual
Page 81
75
APPENDIX
●
READING COMMAND TABLES
q Command
w Name
e Function of the command
r The format of the Set command is shown. When oblique lines are drawn in the 1st and 2nd columns, there is no Set
command.
t The format of the command for reading the transceiver’s current status is shown. When oblique lines are drawn in
the 1st and 2nd columns, there is no Read command.
y The format of the command output from the transceiver is shown. When oblique lines are drawn in the 1st and 2nd
columns, there is no Answer command.
u The number of command digits is shown.
i Corresponds to the parameter of the command format.
o Corresponds to the Format number in the Parameter Table. For the parameter formats, refer to the Parameter
Table {page 73}.
!0 Indicates the function of the parameter.
COMPUTER CONTROL COMMAND TABLES
Note:
Parameters that have a Parameter Function of “NOT USED” are not supported by this transceiver. Any character except the ASCII control
codes (00 to 1Fh) and the terminator (;) may be entered for those parameters.
Note:
P1 is used for Answer only.
Tuning cannot be started if P2 is in
the THRU state (If P2="0", selecting
"1" for P3 does not start tuning).
P1: RX THRU/IN
P2: TX THRU/IN
1
2
Parameter Format Parameter function
3
4
5
6 7
8
9 10 11 12 13 14
Input
Function
Output
Set
Read
Answer
1
2
3
4
5
6 7
8
9 10 11 12 13 14
1
2
3
4
5
6 7
8
9 10 11 12 13 14
AC
ANTENNA TUNER CONTROL
Antenna Tuner THRU/IN -LINE, and tuning
START/CANCEL
A
C
P2 P3
A
C P1 P2 P3
A
C
;
;
;
P1
P2
P3
30
30
1
TUNE THRU/IN
(Answer Only)
TUNE THRU/IN
TUNE OFF/ON
u
i
o
!0
w
r
t
y
e
q
1
2
Parameter Format Parameter function
3
4
5
6 7
8
9 10 11 12 13 14
Input
Function
Output
Set
Read
Answer
1
2
3
4
5
6 7
8
9 10 11 12 13 14
1
2
3
4
5
6 7
8
9 10 11 12 13 14
AI
AUTO INFORMATION
Auto information OFF/ON
A
I P1
A
I P1 ;
A
I
;
;
P1
32
AI NUMBER
Note: For other commands,
controls whether changing a
parameter will or will not trigger the
corresponding Answer command
to be output.
Ex: For IF, the Answer command is
output if the step frequency or
RIT/XIT frequency is changed.
Switching the transceiver ON
restores "0".
Note:
P1 is used for Answer only.
Tuning cannot be started if P2 is in
the THRU state (If P2="0", selecting
"1" for P3 does not start tuning).
P1: RX THRU/IN
P2: TX THRU/IN
1
2
Parameter Format Parameter function
3
4
5
6 7
8
9 10 11 12 13 14
Input
Function
Output
Set
Read
Answer
1
2
3
4
5
6 7
8
9 10 11 12 13 14
1
2
3
4
5
6 7
8
9 10 11 12 13 14
AC
ANTENNA TUNER CONTROL
Antenna Tuner THRU/IN -LINE, and tuning
START/CANCEL
A
C
P2 P3
A
C P1 P2 P3
A
C
;
;
;
P1
P2
P3
30
30
1
TUNE THRU/IN
(Answer Only)
TUNE THRU/IN
TUNE OFF/ON
P1
33
ANTENNA
NUMBER
1
2
Parameter Format Parameter function
3
4
5
6 7
8
9 10 11 12 13 14
Input
Function
Output
Set
Read
Answer
1
2
3
4
5
6 7
8
9 10 11 12 13 14
1
2
3
4
5
6 7
8
9 10 11 12 13 14
AN
ANTENNA NUMBER
Selects antenna connector ANT 1/ ANT 2.
A
N P1
A
N P1 ;
A
N
;
;
P1
31
AF GAIN
1
2
Parameter Format Parameter function
3
4
5
6 7
8
9 10 11 12 13 14
Input
Function
Output
Set
Read
Answer
1
2
3
4
5
6 7
8
9 10 11 12 13 14
1
2
3
4
5
6 7
8
9 10 11 12 13 14
AG
AF GAIN
Sets or reads AF gain.
P1
A
G
;
A
G
;
A
G
P1
;