Kenwood DIGITAL MEDIA RECEIVER KIV-700 - Manual (Page 50)

50
| KIV-700
Bluetooth Setup (Optional)
Bluetooth Setting
You can select following Bluetooth Setting items.
1
Enter Bluetooth mode
Press the [TI] button for at least 1 second.
2
Turn the [Volume] knob and press it when the
desired item is displayed.
Select “BT Settings”.
3
Select the setting item to adjust
Turn the [Volume] knob and press it when the
desired item is displayed.
Display Overview
“SMS Inbox” Display the received short message.
Refer to <Display the SMS> (page 56) .
“BT Settings”
“Phone Selection” Select a cell-phone or Bluetooth audio player
connection.
Refer to <Selecting the Bluetooth Device You
Wish to Connect> (page 52) .
“Audio Selection”
“SMS Download” Download a short message.
Refer to <Downloading the SMS> (page 56) .
“Voice Tag” Registers voice for voice recognition and voice
to select the Phone number category in Phone
book.
- Adding a Voice Dialing Command (page 54)
- Setting a Voice Command for Category (page
55)
“Detailed Setup” Move to detailed item.
“Device
Registration”
Register a Bluetooth device (pairing).
Refer to <Registering Bluetooth Device>
(page 51) . “Special Device
Select”
“Device Delete” Cancel registration of the Bluetooth device.
Refer to <Deleting a Registered Bluetooth
Device> (page 53) .
“PIN Code Edit” Specify the PIN code required when registering
this unit using the Bluetooth device.
Refer to <Registering PIN Code> (page 52) .
“Auto Answer” Answer a call automatically after lapse of the
preset time interval for automatic answer.
“OFF”/ “0s” – “8s” – “99s”
“Bluetooth HF/
Audio”
You can specify output speakers for hands-free
voice communication and Bluetooth audio
sound.
“Front”: Outputs voice from the front speakers.
“All”: Outputs voice from the front and rear
speakers.
“Call Beep” You can output a beep from the speaker when
a call comes in.
“ON”: Beep is heard.
“OFF”: Beep is canceled.
“BT F/W Update” Display the version of the firmware of this unit.
“Mic Gain”*
1 Adjust the sensitivity of the microphone for a
telephone call. Adjust the voice of caller. Setting
to “+” increases the voice volume.
“–3” – “0” – “+3”
“Noise
Reduction”* 1
Reduce the noises generated by surrounding
environment without changing the microphone
volume. Adjust the voice of caller when it is
not clear. Setting to “+” increases the noise
reduction.
“–3” – “0” – “+3”
“Echo Cancel
Level”* 1
Adjust the level of echo cancellation. Setting to
“+” increases the echo cancel reduction.
“–2” – “0” – “+2”
( : Factory setting)
* 1 Function of KCA-BT300 (Optional Accessory)
4
Make a setting
Turn the [Volume] knob to select a setting
value, and then press the [Volume] knob.
5
Exit BT Setting mode
Press the [MENU] button for at least 1 second.
Remarks
• “Auto Answer” (Setting the Time Interval for Automatic
Answer)
This function automatically answers (responds to) a call
after lapse of the preset time interval for automatic answer.
“OFF” : Does not answer the phone call automatically.
“0” : Automatically answers the phone call at once.
“1s” – “99s” : Automatically answers the phone call after
lapse of 1 – 99 seconds.
⁄
• If the time set in the cell-phone is shorter than that set in
the unit, the former will be used.
• This function does not work for call waiting.
• “BT F/W Update” (Displaying the Firmware Version)
Display the version of the firmware of this unit.
For how to update the firmware, access our web site.
http://www.kenwood.com/cs/ce/bt/
SRC MENU Volume