Kenwood KRF-V8010D - Manual (Page 25)

25
Operations
KRF-V8010D (En/T)
Convenient functions
SOUND
TUNING/SKIP
SUBWOOFER
VOLUME
MULTI CONTROL
SOUND
DISPLAY
Adjusting the sound
You can make further adjustments to the sound while listening to
playback in the surround mode.
1 Press the SOUND key to select the item you want to adjust.
Each press switches the selection as listed below.
Note that some items are not displayed in certain modes.
BASS (low frequency range sound quality adjustment) ^
TREB (high frequency range sound quality adjustment) ^
Cch (center speaker level adjustment)
RS (right surround speaker level adjustment)
LS (left surround speaker level adjustment)
SW (subwoofer level adjustment)
INPUT (input level adjustment) %
NIGHT (midnight mode on/off) ∞
2 Use the MULTI CONTROL (TUNING/SKIP) to adjust the setting
as desired.
• The adjustment item is displayed for approximately eight sec-
onds.
• If you used the remote control to perform the above setting, press
the VIDEO key at this point to turn off the remote control’s own
adjustment mode. In this case, the input source is not switched.
Midnight mode (Dolby Digital (AC-3) mode only)
When watching movies at night you might not be able to raise the
volume as loud as normal. Midnight mode compresses the dynamic
range of previously specified parts of the Dolby Digital (AC-3) sound
track (like scenes with sudden increases in volume) to minimize the
difference in volume between the specified and non-specified parts.
This makes it easy to hear all of the sound track, even when listening
at low volumes.
1 Press the SOUND key several times until “NIGHT” is displayed.
• This can be selected only if VIDEO2 or VIDEO3 is selected as the
source and the input mode is set to digital.
2 Use the MULTI CONTROL (TUNING/SKIP) to select the on or off
setting.
SUBWOOFER adjustment
Note
To enjoy Dolby Digital (AC-3) surround (as well as all the other
listening modes) from a single component, be sure to use a Dolby
Digital (AC-3) compatible source component. Connect the Dolby
Digital (AC-3) compatible source component's Dolby Digital (AC-3)
format digital audio signal to one of the DIGITAL INPUT jacks on the
back of the receiver. Connect the normal audio signal correctly to the
respective component's AUDIO jacks.
78
• The adjustment item is displayed for approximately eight sec-
onds.
• Some Dolby Digital (AC-3) software may not be compatible with
the Midnight mode.
• If you used the remote control to perform the above setting, press
the VIDEO key at this point to turn off the remote control’s own
adjustment mode. In this case, the input source is not switched.
It is easy to adjust the volume of the subwoofer using the remote
control.
1 Press the SUBWOOFER key so that “SW” is displayed.
2 Use the VOLUME key to adjust the volume.
• The adjustable range is -10 dB to +10 dB.
Display dimmer adjustent
The dimmer function lets you select the brightness of the receiver's
display. You might find this useful if you darken your room to watch
movies or listen to music.
Each time you hold down the DISPLAY key for more than two
seconds, the display brightness changes among the three avail-
able settings. Select the brightness level you find most pleas-
ing.
sW d B )
A SP
TUNED
MEMO.
AUTO
ST.
AUTO SOUND C
RS
R
LS
L
LFE
DIGITAL B
VIDEO1
A SP
PRO LOGIC
S
SW
C R L B
VIDEO1 A SP
PRO LOGIC
S
SW
C R L B
VIDEO1 A SP
PRO LOGIC
S
SW
C R L B
Ambience effects
NIGHT N O
A SP
TUNED
MEMO.
AUTO
ST.
AUTO SOUND C
RS
R
LS
L
LFE
DIGITAL B