KORG D8 - Manual (Page 57)

58
21. TRACK STATUS
Track status select .....................................................
[PLAY, REC (ANALOG), REC (DIGITAL), Mute]
Selects the status of each track.
✧ Each time you press the [TRACK STATUS] key, the
function will change and the indicator color will
change to show this.
PLAY (indicator lit green): The selected track can be
played back.
REC (ANALOG)
(indicator blinking/lit red): This can
be selected when [REC SELECT] is INPUT 1/2 or
MASTER
. Audio from the external input jacks INPUT
1/2 or from the master bus can be recorded to the
selected track. The indicator will blink during record-
ready condition, and will light during recording (or
rehearsal).
REC (DIGITAL)
(indicator blinking/lit orange): This
can be selected when [REC SELECT] is DIGITAL IN.
The external input from the DIGITAL IN connector can
be recorded to the selected track. The indicator will
blink during record-ready condition, and will light
during recording (or rehearsal).
It is not possible to input from the internal effect or
from an external input via the AUX IN jacks.
MUTE
(indicator off): The selected track will be
muted.
When input monitor (refer to p.47) is set to AUTO, set-
ting [TRACK STATUS] to REC will cause the EQ and
fader to apply only to the input sound, so that the
fader and EQ will not affect the playback sound of the
track. Be aware that if you inadvertently change the
fader or EQ settings during playback etc., the volume
or EQ of the input sound will be affected.
However if [REC SELECT] is set to MASTER, it will be
the same as when [TRACK STATUS] is set to PLAY;
you will always hear the playback tracks, and faders
and EQ will be valid.
Pairing (refer to PAIR On/Off) is also possible.
22. EQ
High EQ gain adjustment
P1-1 Channel number display...........................................
[1, 2, 3, 4, 5, 6, 1-2, 3-4, 5-6, 7-8]
This shows the currently selected channel number.
1-2
, 3-4 and 5-6 will appear when Pairing is On (refer
to PAIR On/Off).
P1-2 HEQ (Fc=10 kHz) gain setting.........[-15...+00...+15]
The boost/cut at the 10 kHz cutoff frequency can be
adjusted over a range of -15–+15 dB.
Low EQ gain adjustment
P2-1 Channel number display ..................................
[1, 2, 3, 4, 5, 6, 1-2, 3-4, 5-6, 7-8]
This shows the currently selected channel number.
1-2
, 3-4 and 5-6 will appear when Pairing is On (refer
to PAIR On/Off).
P2-2 LEQ (Fc=100 Hz) gain setting..........[-15...+00...+15]
The boost/cut at the 100 Hz cutoff frequency can be
adjusted over a range of -15–+15 dB.
High EQ and Low EQ can be paired (refer to PAIR On/
Off), and registered as part of a scene (refer to SCENE).
23. EFFECT SEND
Effect send level (Snd) adjustment
Adjusts the level that is sent from after each channel
fader (post fader) to the internal effect.
Adjust this setting when you use the internal effect.
When [REC SELECT] DIGITAL IN is selected, the
internal effect will be off.
TRACK STATUS=REC
TRACK STATUS=REC
TRACK STATUS=PLAY
INPUT
FADER
HEQ LEQ
FADER
[EQ]
HEQ LEQ
TRACK
INPUT
TRACK
INPUT
TRACK
[EQ]
[EQ]
FADER
HEQ LEQ
[EQ]
Recording
Playback
Playback
EQ and fader
will apply to the
input sound and
will affect the
recording
EQ and fader
will not affect
the playback
EQ and fader
will apply to
the playback
P1
1 2
HEQ1 :+00
P2
1 2
LEQ1 :+00
P1
1 2
Snd1 :000