KORG CX-3 - Manual (Page 26)

Parameters
22
2. Global mode
In Global mode you can press PROGRAM [1]–[8]
keys to directly select the first parameter in Group 1–
Group 8 as listed below.
Group 1
Set the master tuning, and the expression pedal and
pedal switch functions.
Group 2
Set the MIDI channel.
Group 3
Set the velocity value of MIDI note messages, and the
pitch bend range.
Group 4
Set MIDI filters.
Group 5
Set the MIDI control change numbers used to transmit
and receive drawbar settings.
Group 6
Set the MIDI control change numbers assigned to
front panel keys and to connected pedals.
Group 7
Copy, swap, initialize programs, and dump data.
Group 8
Play the demo songs.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Group 1
Master Tune [–430.0Hz...+450.0Hz]
This adjust the overall pitch of the entire CX-3 in 0.2
Hz steps, relative to the reference pitch of A4 (middle
of A).
Transpose [–12...+12]
Adjust the pitch in semitone steps over a range of
±
1
octave.
Exp Minimum Level (Expression Minimum Level) [0...30]
Specify the minimum level when the expression pedal
etc. is operated.
This will be the volume when the controller selected
by the “Exp Control” parameter is at its minimum
level.
Exp Control (Expression Controller) [Both, Knob, Pedal]
Both: The front panel [EXPRESSION/OVERDRIVE]
knob and the expression pedal etc. connected to the
rear panel EXPRESSION PEDAL jack will both control
the volume. These two will function simultaneously.
Knob:
The [EXPRESSION/OVERDRIVE] knob will
control the volume.
Pedal:
The expression pedal connected to the rear
panel EXPRESSION PEDAL jack will control the
volume.
Prog Up Ctrl (Program Up Controller)
[Off, Pedal 1/(Pdl 1), Pedal 2/(Pdl 2)]
Pedal 1: A pedal switch connected to the rear panel
ASSIGNABLE PEDAL/SW 1 jack can be used to switch
programs. When you press the pedal switch, the pro-
gram number will be incremented in steps of one.
Pedal 2:
A pedal switch connected to the rear panel
ASSIGNABLE PEDAL/SW 2 jack can be used to
perform the above function.
Off:
No function.
(Pdl 1), (Pdl 2): This indicates that the same pedal
switch is selected for the “Prog Down Ctrl” parameter
described below. Please select a different pedal switch.
If the same pedal switch as selected for this param-
eter is also selected for a Normal Edit mode or EX
Edit mode parameter, this (Global mode) setting will
take priority, and the Normal Edit mode or EX Edit
mode setting will be ignored.
Porg Down Ctrl (Program Down Controller)
[Off, Pedal 1/(Pdl 1), Pedal 2/(Pdl 2)]
Pedal 1: A pedal switch connected to the rear panel
ASSIGNABLE PEDAL/SW 1 jack can be used to switch
programs. When you press the pedal switch, the pro-
gram number will be decremented in steps of one.
Pedal 2:
A pedal switch connected to the rear panel
ASSIGNABLE PEDAL/SW 2 jack can be used to
perform the above function.
Off:
No function.
(Pdl 1), (Pdl 2): This indicates that the same pedal
switch is selected for the “Prog Down Ctrl” parameter
described above. Please select a different pedal switch.
If the same pedal switch as selected for this param-
eter is also selected for a Normal Edit mode or EX
Edit mode parameter, this (Global mode) setting will
take priority, and the Normal Edit mode or EX Edit
mode setting will be ignored.