KORG CX-3 - Manual (Page 30)

Parameters
26
Dump Program (Dump One Program)
This command dumps the data for the single program
you specify. For details refer to “MIDI data dump”
(p.28).
Dump Program All (Dump All Programs)
This command dumps the data for all programs. For
details refer to “MIDI data dump” (p.28).
Dump Global (Dump Global Parameter)
This command dumps global data. For details refer to
“MIDI data dump” (p.28).
Dump All Prog + Global (Dump All Program and
Global Parameter)
This command dumps all program data and global
data. For details refer to “MIDI data dump” (p.28).
Drawbar Scan
When the CX-3 receives MIDI control changes, the
drawbar registers will be modified, which will mean
that the sound will no longer match the Drawbar 1 or
2 settings of the front panel.
When you execute this command, the levels of
Drawbar 1 and 2 will be scanned, and their values will
be loaded into the drawbar register.
Execute this command when you want the sound to
reflect the Drawbar 1 or 2 settings.
Default DB Select (Drfault Drawbar Select)
This registers the current setting of the DRAWBAR
SELECT section as the default for when the power is
turned on.
Exp Pd 1 Calibration (Expression Pedal 1 Calibration)
If the expression pedal connected to the rear panel
EXPRESSION PEDAL jack does not produce the
correct amount of control when it is operated, use the
following procedure to adjust the sensitivity of the
expression pedal.
1 . Connect an expression pedal to the EXPRESSION
PEDAL jack.
2 . Sel ect t hi s command.
3 . Press the [WRITE/ENTER] key.
The display will indicate Set Minimum.
4 . Move the expr essi on pedal to it s mi ni mum posi ti on,
and press the [WRITE/ENTER] key.
The display will indicate Set Max.
5 . Move the expr essi on pedal to it s maxi mum posi ti on,
and press the [WRITE/ENTER] key.
Wheel Brake
This simulates the rotation of the wheel that occurs
when the power of a combo organ is turned on/off.
When you press the [WRITE/ENTER] key, the wheel
rotation will gradually slow down and stop. Press the
[WRITE/ENTER] key once again, and the wheel will
gradually resume rotating.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Group 8
DEMO Play [1...9]
Here you can select and play the demo songs.
For details refer to “5. Listening to the demo songs”
(p.13).
Type 1 Ex Drawbar 1 [G4...C7]
Specify the sound that will be assigned to the left-
most bar (16') of the EX Drawbars (Drawbar 2) used in
an EX program.
This setting will be used if the EX Edit mode Group 2
“EX Drawbar Type” parameter is set to 1.
Type 1 Ex Drawbar 2 [G4...C7]
Specify the sound that will be assigned to the second
bar from the left (5-1/3') of the EX Drawbars (Draw-
bar 2) used in an EX program.
This setting will be used if the EX Edit mode Group 2
“EX Drawbar Type” parameter is set to 1.
Type 1 Ex Drawbar 3 [G4...C7]
Specify the sound that will be assigned to the third bar
from the left (8') of the EX Drawbars (Drawbar 2) used
in an EX program.
This setting will be used if the EX Edit mode Group 2
“EX Drawbar Type” parameter is set to 1.
Type 1 Ex Drawbar 4 [G4...C7]
Specify the sound that will be assigned to the right-
most bar (4') of the EX Drawbars (Drawbar 2) used in
an EX program.
This setting will be used if the EX Edit mode Group 2
“EX Drawbar Type” parameter is set to 1.
Type 2 Ex Drawbar 1 [G4...C7]
Type 2 Ex Drawbar 2 [G4...C7]
Type 2 Ex Drawbar 3 [G4...C7]
Type 2 Ex Drawbar 4 [G4...C7]
Specify the sounds that will be assigned to the EX
Drawbars (Drawbar 2) used in an EX program.
These settings will be used if the EX Edit mode Group
2 “EX Drawbar Type” parameter is set to 2.
Type 3 Ex Drawbar 1 [G4...C7]
Type 3 Ex Drawbar 2 [G4...C7]
Type 3 Ex Drawbar 3 [G4...C7]
Type 3 Ex Drawbar 4 [G4...C7]
Specify the sounds that will be assigned to the EX
Drawbars (Drawbar 2) used in an EX program.
These settings will be used if the EX Edit mode Group
2 “EX Drawbar Type” parameter is set to 3.
Type 4 Ex Drawbar 1 [G4...C7]
Type 4 Ex Drawbar 2 [G4...C7]
Type 4 Ex Drawbar 3 [G4...C7]
Type 4 Ex Drawbar 4 [G4...C7]
Specify the sounds that will be assigned to the EX
Drawbars (Drawbar 2) used in an EX program.
These settings will be used if the EX Edit mode Group
2 “EX Drawbar Type” parameter is set to 4.
Since notes above F#8 on the CX-3 are “wrapped
around” so that they will sound an octave lower, we
recommend that you play keys in the bottom octave
of the CX-3 when checking these notes.