Creating a fade-out, Operation – KORG D3200 User Manual
Page 87
77
Recovery
CD
Creating a fade-out
Fading-out the IN–OUT region of track 1
(1) Specify the region that you want to fade-out.
Set the following locations to specify the region where
the fade-out will occur (
• Set the IN point to specify the beginning of the region
where the fade-out will occur.
• Set the OUT point to specify the end of the region
where the fade-out will occur.
(2) Select “FadeTrk.”
In the TRACK, “EditTrk” tab page, click the Edit Trk
Type
cell. In the Edit Trk Type dialog box, click “Fade-
Trk”
and click the OK button (or press the panel YES
key).
(3) Select the fade-out curve.
Click the Mode button to display the Fade Mode dialog
box.
A.B.C:
Fade-in curve
D.E.F:
Fade-out curve
For details on how these curves differ, refer to “Fade-
Trk”
For this example, select the type “D” curve and click the
OK
button (or press the panel YES key) to return to the
“EditTrk”
tab page.
(4) Select the track number that you want to fade-out.
• Click the popup button of the Destination cell, and
choose track “1” in the Destination Track dialog box.
You can also click the cell to select this.
• Check the IN and OUT locations. If you want to set
the locations with more precision, click the Destina-
tion WAVE
button, and use the Wave dialog box
(5) Execute the editing operation.
Click the Exec. button. Then in the FadeTrk dialog box,
click the Yes button (or press the panel YES key) to exe-
cute the operation.
When the operation is finished, the display will indicate
“Completed.”
Click the OK button (or press the panel
YES
key).
(6) Check the results of the editing operation.
Press the LOC 1/IN key, and play back from the IN loca-
tion to verify that the operation has done correctly.
If you are not satisfied with the results, you can use
Undo to return to the previous state. (
The length of the IN–OUT area specified will determine the
amount of time it takes to complete the Fade operation.
Boosting the maximum volume to the specified
level (Normalize: NormalizeTrk)
If the recorded level of a track is too low, you can use the Nor-
malize operation to boost the overall level of the specified re-
gion (IN–OUT) so that the maximum recorded level will
equal the specified level.
• You can normalize one track or simultaneously normalize
the data of adjacent tracks.
If you boost data that was recorded at an extremely low level, any
noise in that region will also be boosted.
Normalizing the IN–OUT region of track 1
(1) Specify the region that you want to normalize.
Set the following locations to specify the region for nor-
malize (
• Set the IN point to specify the beginning of the region
to be normalized.
• Set the OUT point to specify the end of the region to
be normalized.
(2) Select “NormalizeTrk.”
In the TRACK, “EditTrk” tab page, click the Edit Trk
Type
cell. In the Edit Trk Type dialog box, click
“NormalizeTrk”
and click the OK button (or press the
panel YES key).
(3) Specify the maximum level.
Click the Mode button to display the Normalize Mode
dialog box. Set the “Normalize Gain Level” value, and
click the OK button (or press the panel YES key).
(4) Select the track number that you want to normalize.
• Click the popup button of the Destination cell, and
choose track “1” in the Destination Track dialog box.
You can also click the cell to select this.
• Check the IN and OUT locations. If you want to set
the locations with more precision, click the Destina-
tion WAVE
button, and use the Wave dialog box
(
→p.128) to set the location.
(5) Execute the editing operation.
Click the Exec. button. Then in the NormalizeTrk dialog
box, click the Yes button (or press the panel YES key) to
execute the operation.
When the operation is finished, the display will indicate
“Completed.”
Click the OK button (or press the panel
YES
key).
(6) Check the results of the editing operation.
Press the LOC 1/IN key, and play back from the IN loca-
tion to verify that the data was normalize correctly.
If you are not satisfied with the results, you can use
Undo to return to the previous state. (
The length of the IN–OUT area specified will determine the
amount of time it takes to complete the Normalize operation.
(2)
(4)
(3)
(5)