Kenwood KRF-X9050D - Manual (Page 21)

21
Preparation
Preparing for surround sound
4 Use the MULTI CONTROL knob or keys to select the
appropriate front speakers setting.
1 NML/THX (normal) : Average size front speakers are
connected to the receiver.
2 LRG (large) : Large front speakers are connected to
the receiver.
• Under certain circumstances , for “FRONT LRG” selection, no sound
will be heard from the subwoofer even when it is set to ON. However,
if you select SW RE-MIX ON when subwoofer is selected, you may
hear sound from the subwoofer.
5 Press the SET UP key to accept the setting.
• The center speaker setting indication “CENTER” scrolls across the
display.
If you have selected “NML” as the front speakers setting,
1 NML/THX : Center speaker setting mode to
the receiver is ON.
2 OFF : Center speaker setting mode to the
receiver is OFF.
7 Press the SET UP key to accept the setting.
• The surround speaker setting indication “SURROUND” scrolls
across the display.
8 Use the MULTI CONTROL knob or keys to select the appropri-
ate surround speaker setting,
If you have selected “LRG” as the center speaker setting,
1 NML/THX (normal) : Average size surround speakers are
connected to the receiver.
2 LRG (large) : Large surround speakers are
connected to the receiver.
3 OFF : Surround speaker setting mode to
the receiver is OFF.
If you have selected other than “LRG” as the center
speaker setting,
1 NML/THX : Surround speaker setting mode to
the receiver is ON.
2 OFF : Surround speaker setting mode to
the receiver is OFF.
9 Press the SET UP key to accept the setting.
• The subwoofer remix setting indication “SW RE-MIX” scrolls
across the display.
Select the subwoofer re-mix setting.
1 Use the MULTI CONTROL knob or keys to select the
appropriate subwoofer remix setting.
1 ON : Subwoofer re-mix set mode to the receiver is ON.
2 OFF : Subwoofer re-mix set mode to the receiver is OFF.
This is the THX preferred setting.
6 Use the have MULTI CONTROL knob or keys to select the
appropriate center speaker setting.
If you selected “LRG” as the front speakers setting,
1 NML/THX (normal) : An average size center speaker is
connected to the receiver.
2 LRG (large) : A large center speaker is connected
to the receiver.
3 OFF : Center speaker setting mode to the
receiver is OFF.
MEMO
ST.
TUNED
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
AUTO SOUND AUTO
CLIP LFE SW
S RS LS
B
MUTE
TI.VOL
RDS EON PTY
TP TA NEWS
STEREO
C SP A L R
Blinks
3
“SW RE-MIX” scrolls across the display
TI.VOL B
CLIP MUTE
RDS EON PTY
TP TA NEWS
SP A FM
AM
MHz
kHz
PRO LOGIC
DOWN MIX
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
STEREO 3
DIGITAL AUTO SOUND AUTO
SW
L R
2 Press the SET UP key to accept the setting.
• The receiver enters the speaker volume level adjustment
mode.
• In step 4, indications appear only for the selected channels of
the speakers that require adjusting.
1 Press the SET UP key such that the subwoofer setting indica-
tion “SUBWOOFER” scrolls across the display.
“SUBWOOFER” will be scrolled from right to left
Blinks
2 Use the MULTI CONTROL knob or keys to select the appro-
priate subwoofer setting.
1 ON : Subwoofer setting mode to the receiver is ON.
2 OFF : Subwoofer setting mode to the receiver is OFF.
• The initial setting is “SUBWOOFER ON”.
• When “SUBWOOFER OFF” is selected, the front speakers are
automatically set to “LRG” and the procedure skips to step 5.
• When subwoofer output sound is required, select “FRONT NML”.
To enable you to obtain optimum enjoyment from the receiver’s listening
modes, make sure to complete the speaker settings (subwoofer, front,
center, and surround speakers) as described below.
1
2
Turn on the power to this receiver by pressing POWER and
ON/STANDBY ( ) or POWER ( ) keys.
Select a speaker system.
Speaker settings
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO
LFE
C
S RS LS
TI.VOL B
CLIP MUTE
RDS EON PTY
TP TA NEWS
SP A
STEREO SW
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND AUTO C
S RS
TI.VOL B
CLIP MUTE
RDS EON PTY
TP TA NEWS
R SP A
STEREO LS
SW
3 Press the SET UP key to accept the setting.
• The front speakers setting indication “FRONT” scrolls across the
display.
Blinks
MULTI CONTROL
SET UP
ON/STANDBY( )
POWER
POWER
RC-R0714 RC-R0715
MULTI
CONTROL
SET UP SET UP
Continued to next page