Kenwood KRF-X9050D - Manual (Page 26)

26
Operations
Listening to radio broadcasts
1
2
3
Each press switches the tuning method as follows:
4
Auto tuning : The next station is tuned automatically.
Manual tuning : Turn the knob (or press the keys) to select the
desired station.
Each press switches the band
as follows:
1 AUTO lit (auto tuning)
2 AUTO not lit (manual tuning)
Tuning radio stations
Frequency
display
“ TUNED ” is displayed
when a station is received.
• Normally, set to “ AUTO ” (auto tuning). If the radio waves are weak
and there is a lot of interference, switch to manual tuning. (With
manual tuning, stereo broadcasts will be received in monaural.)
“ AM ” or “ FM ” indicator appears
in the display.
Use the INPUT SELECTOR knob (TUNER key) to select the
tuner.
Use the BAND key to select the desired broadcast band.
Use the AUTO key to select the desired tuning method.
Use the MULTI CONTROL knob or TUNING 1/ ¡ keys
to select the station.
1 FM
2 AM
Presetting radio stations manually
• Repeat steps 1, 2, 3, and 4 to store as many stations as necessary.
• If you store a station at a previously used preset, the old station will
be replaced by the new one.
Press the MEMORY key while receiving the station.
Proceed to step 3 within 5 seconds.
(If more than 5 seconds elapse, press the MEMORY key again).
Blinks for 5 seconds Lights for 5 seconds
1
2
Tune to the station you want to store.
3
4
Receiving preset stations
Enter the number of the preset you want to receive (up to
“40”).
1
2
Press the numeric keys in the following order:
For “15”, press .......... 0 , 5
For “20”, press .......... 0 , 0 , )
• If you make a mistake entering a two digit number, press the +10 key
repeatedly to return to the original display and start again.
“ ST. ” lights up when a broadcast
is being received in stereo.
Use the MULTI CONTROL knob or keys to select one of the
station presets (1 – 40).
Press the MEMORY key again to accept the setting.
Use the TUNER key to select the tuner as the source.
AM
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND FM
MHz STEREO
AUTO
AM
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND FM
MHz STEREO
AUTO
AM
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
AUTO SOUND
MEMO
FM
MHz STEREO
AUTO
TUNED
ST.
AM
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
AUTO SOUND
LFE
C
S RS LS
TI.VOL B
CLIP MUTE
RDS EON PTY
TP TA NEWS
FM
MHz STEREO
AUTO
TUNED
ST.
MEMO
SW
R L SP A
“ AUTO ” indicator lights
up in the display.
The receiver can store up to 40 stations in the memory and recall them by
one-touch operation.
Radio stations can be classified into RDS (Radio Data System) stations
and other stations. To listen to or store RDS stations in the preset memory
see “Using RDS (Radio Data System)”. (For U.K. only)
AM
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
AUTO SOUND
LFE
C
S RS LS
TI.VOL B
CLIP MUTE
RDS EON PTY
TP TA NEWS
FM
MHz STEREO
AUTO
TUNED
ST.
MEMO
SW
R L SP A
The RDS auto memory function assigns preset numbers to RDS stations
starting from preset number “1”. Therefore, be sure to execute the RDS
auto memory function before using the following operations to manually
store AM stations and other FM stations, and RDS stations. See “Presetting
RDS stations (RDS AUTO MEMORY)”. (For U.K. only)
•
MULTI CONTROL
INPUT SELECTOR
BAND AUTO
RC-R0714 RC-R0715
MULTI
CONTROL
AUTO AUTO
TUNER
TUNING 1 / ¡ TUNING 1 / ¡
BAND
BAND
TUNER
MULTI CONTROL
MEMORY
RC-R0714 RC-R0715
Numeric keys
TUNER