Cloning procedures (cont.) – LG STB1000 User Manual

Page 56

Advertising
background image

56

206-4147

Cloning Procedures (Cont.)

Learning / Teaching a Master STB1000 Setup using an LT2002 Clone Programmer (Cont.)

Learn Setup from Master STB1000
1. Ensure the Master STB is set up completely and the EBL is in Pass-

through Mode.

2. If an analog channel is not available, direct tune the Master STB1000

to an Aux source, or select an Aux source, such as AV-1, from the Input
Menu. Then, plug one end of the MPI cable into the MPI port on the STB
jack panel.

3. If there is a good connection after the LT2002 is connected to the STB

MPI port, “THE CLONE HAS CONTROL OF THE TV” message will
appear on the display panel screen. Press any key on the Installer
Remote to access the LT2002 Clone Selection Menu.

4. Press 1 on the Installer Remote to select LEARN FROM TV from the

Clone Selection Menu; then press ENTER to proceed to the Memory
Bank Selection Menu.

5. Press 1, 2, or 3 on the Installer Remote to select the clone Memory

Bank in which to store the Master Setup. Then, press ENTER.

Note: If you choose a Memory Bank that already has a Master device’s

setup programmed into it, that setup will be overwritten by the new Mas-
ter STB Setup.

6. Verify the Learning setup information on the next screen, and then

press POWER to transfer the Master STB Setup into the selected
Memory Bank on the LT2002.

Learning usually takes about 90 seconds. “LEARNING IN PROG-

RESS” will be displayed on the screen while the LT2002 copies the
Master Setup. When the Learning process is complete, a “LEARNING
COMPLETE” message will be displayed.

7. When Learning is complete, disconnect the MPI cable from the Master

STB1000.

(Optional) Set the Clock
Set the time on a Master STB’s clock. (If the time has already been copied
from a TV into the LT2002 clone programmer, you can set the Master
STB’s clock by copying the time from the clone programmer.) The LT2002
can copy the current time to both a Master STB and to the clone’s internal
clock—accurate to within one minute. (Another reason the LT2002 should
be equipped with fresh, high-quality alkaline batteries, is for it to keep the
time as accurately as possible.)
Since the LT2002’s time cannot be set directly, the current time needs to
be copied from an LG STB equipped with an enabled MPI port.
After the time is copied to the LT2002 clone programmer, the current time
will be maintained and can then be transferred to another STB. (This can
be a Master STB or another STB which has already had the features set
up.)

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX
THE TV IS VERSION XX
THE SW IS REVISION XX

CLONE CLOCK = XX:XX
TV CLOCK = XX:XX

- PRESS ANY KEY TO CONTINUE.

- DISCONNECT CLONE WHEN DONE.

CLONE SELECTION MENU

(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP

-

-

TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.

TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.

SAVE TV SETUP IN SELECTED
CLONE MEMORY

(1) MEMORY 1 VER XX REV XX
(2) MEMORY 2 VER XX REV XX
(3) MEMORY 3 VER XX REV XX
(4) RETURN TO CLONE MENU

-

-

TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.

TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.

CLONE SELECTION MENU

(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP

-

-

TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.

TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.

Advertising