Panasonic AJ-SDd93 - Manual (Page 24)

– 24 –
Setup menus (continued)
The underlined items indicates the initial setting.
USER menu <OPERATION>
No./Item Description No./Item Description
115
EJECT SW
INH
This selects whether to enable or
disable the operation of the EJECT
button on the front panel.
0000 REC :
Operation is disabled while the unit
is in the recording mode.
0001 OFF :
Operation is enabled in all modes.
120
EJECT EE SEL
This selects the modes for the
picture and sound output when the
tape is ejected.
0000 EE : EE mode
0001 BLACK :
The picture turns black, and the
sound is muted.
0002 GRAY :
The picture turns gray, and the
sound is muted.
Note:
The IEEE 1394 digital output video will
be black even if GRAY is selected.
121
F/R EE SEL
This selects whether the EE mode or
playback mode is to be established
during fast forwarding or rewinding.
0000 EE : EE mode
0001 TAPE : Playback mode
122
STOP EE SEL
This select whether the EE mode or
playback mode is to be established
when operation is stopped.
0000 EE : EE mode
0001 TAPE : Playback mode
Note:
The selection is complied with even in the
standby OFF mode. However, the picture
will turn gray (black for IEEE 1394 digital
output) when TAPE is selected.
160
MEMORY
MODE
This sets the repeat play mode.
0000 OFF :
No repeat play (normal operation)
0001 M-STOP :
The tape stops near the BEGIN point when a
FF or REW operation has been performed.
0002 REPT1 :
During playback, the tape is rewound to the
BEGIN point and stopped when the END
point is reached.
0003 CONT :
During playback, the tape is rewound to the
BEGIN point and then played, and these
steps are repeated when the END point is
reached.
161
CTL BGN
or
TC BGN
This sets the BEGIN point in the
repeat play mode.
Whether TC or CTL is displayed on the counter
when the COUNTER button is pressed is set
here. When there is no setting, --:--:--:-- appears,
and the tape start serves as the BEGIN point.
162
END
This sets the END point in the
repeat play mode.
Whether TC or CTL is displayed on the counter
when the COUNTER button is pressed is set
here. When there is no setting, --:--:--:-- appears,
and the tape end serves as the END point.
163
REPT MODE
This sets the output image when the
tape returns to the BEGIN point in
the repeat play mode.
0000 FREEZE :
The tape returns to the BEGIN point
while the playback image at the
END point remains frozen.
0001 BLACK :
The tape returns to the BEGIN point while
a BLACK picture remains on the screen.
0002 EE_SEL :
The tape returns to the BEGIN point
with an image which is in
compliance with the setup menu
item No.121 (F/R EE SEL) setting.
Note:
If, when FREEZE has been selected, the
END point has been set at the tape end,
the playback image will not be frozen
properly. Set the END point in a range
where pictures have been recorded.
202
ID SEL
This sets the ID information to be
returned to the controller.
0000 OTHER :
0001 DVCPRO :
0002
ORIG :
Notes:
• ID information of any VTR except for
the DVCPRO’s is set in OTHER.
• The ORIG setting should only be used
when a Panasonic controller (AG-A850
etc. sold separately) is connected.
114
REC INH
LAMP
This selects whether to cause the
REC INH lamp to flash or light up
when the cassette has been set to the
accidental erasure prevention status.
0000 LIGHT : The lamp lights up.
0001 FLASH : The lamp flashes.
Note:
When the REC INHIBIT switch is set to
ON, the REC INH lamp always lights
regardless of the general setting status.
YA93P
USER menu <INTERFACE>
No./Item Description
This appears only when the optional board
AJ-YA93P has been installed. YA93P