Panasonic AJ-SDd93 - Manual (Page 40)

– 40 –
Error messages (continued)
Monitor display Description Priority
High
(Low)
VTR operation
E-04
(UNKNOWN SIG)
This appears when the signals supplied from
the IEEE 1394 digital interface are not
DVCPRO/DV format signals. Check that the 1394
input has been
connected properly.
E-11
(NOT 1x 25M SIG)
This appears when the signals supplied from
the IEEE 1394 digital interface are not
DVCPRO/DV (25 Mbps) format 1x transfer
signals.
Check the 1394 input
signals.
E-12
(NOT 1x 50M SIG)
This appears when the signals supplied from
the IEEE 1394 digital interface are not
DVCPRO50 (50 Mbps) format 1x transfer
signals.
Check the 1394 input
signals.
E-16
(INVALID VIDEO
SIG)
This appears when the compressed video
signals supplied from the IEEE 1394 digital
interface are irregular signals.
• This warning appears only during recording
operations. In such cases, no signals are
recorded on the tape, and only erasure of
existing signals is performed.
Check the 1394 input
signals.It is possible that
playback signals of an
unrecorded tape are
being input.
E-17
(INVALID AUDIO
SIG)
This appears when the audio signals
supplied from the IEEE 1394 digital interface
are irregular signals.
• This warning appears only during recording
operations. In such cases, the signals are
recorded with the audio signals muted.
Check the 1394 input
signals.It is possible that
signals other than 1x
playback signals are
being input from a VTR
or other device.
E-18
(INVALID TC SIG)
This appears when the time code
information supplied from the IEEE 1394
digital interface is irregular information.
• This warning appears only during recording
operations. In such cases, the internally
generated time code is recorded.
Check the time code of
the device which is
supplying the time code.
E-92
(1394 INITIAL
ERROR)
This appears when the connection status of
the IEEE 1394 digital interface is irregular.
If a loop-through format
has been adopted for the
cable connections, re-
connect each of the
cables on a 1:1 basis. If
such a format has not
been adopted, set the
POWER switch to OFF
and then back to ON.
E-10
(FAN STOP) This appears when the fan motor has shut
down. Check the fan for foreign
matter.
E-09
(NO RF)
This appears when a blank section lasting
for more than one second on the tape has
been detected during playback.
A blank section is identified as such when all
the following conditions are met:
• There are no output signals from any of the
heads.
• The playback data cannot be read.
• There is no CTL signal (DV/DVCAM tapes
excluded).
Check the tape. It is
possible that an
unrecorded tape has
been loaded.
E-00
(SERVO NOT
LOCKED) This appears when the servo is not locked
for three or more seconds during playback
or recording.
Check the tape. It is
possible that a tape
recorded by a system
other than 525/60 has
been loaded.
No recording
o p e r a t i o n s
are possible.
No recording
o p e r a t i o n s
are possible.
No recording
o p e r a t i o n s
are possible.
O p e r a t i o n
cannot be
continued.
O p e r a t i o n
cannot be
continued.
O p e r a t i o n
cannot be
continued.
Signal input
and output
through the
IEEE 1394
d i g i t a l
interface is
stopped.
O p e r a t i o n
continues.
O p e r a t i o n
continues.
O p e r a t i o n
continues.
Corrective action
Displaying the warning information
• A warning message appears when a warning has occurred. “NO WARNING” appears when a warning has not occurred.
• When more than one warning has occurred simultaneously, move the joystick up or down to check the description of
each warning.
Warning messages