NEC 50XC10 - Manual (Page 5)

English-2
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THIS
UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS
CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL
SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD
FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Th is symbol warns user that uninsulated voltage within the unit may have suffi cient magnitude to cause electric shock.
Th erefore, it is dangerous to make any kind of contact with any part inside this unit.
Th is symbol alerts the user that important literature concerning the operation and maintenance of this unit has been
included. Th erefore, it should be read carefully in order to avoid any problems.
Important Information
Canadian Department of
Communications Compliance Statement
DOC: Th is Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
FCC Information
1. Use the attached specifi ed cables with the P426Y3(P42XC10),
P506Y4(P50XC10) or P606Y5(P60XC10) color monitor so as not to
interfere with radio and television reception.
(1) Please use the supplied power cord or equivalent to
ensure FCC compliance.
(2) Please use shielded video signal cable,
15-pin mini D-SUB to 15-pin mini D-SUB
with ferrite cores on both ends (not included).
2. Th is equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. Th ese
limits are designed to provide reasonable protection against harmful
interference in a residential installation. Th
is equipment generates, uses,
and can radiate radio frequency energy, and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
diff erent from that to which the receiver is connected.
Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/
television technician for additional suggestions. Th
e user may fi nd the
following booklet, prepared by the Federal Communications Commission,
helpful: “How to Identify and Resolve Radio-TV Interference Problems.” Th
is
booklet is available from the U.S. Government Printing Offi ce, Washington,
D.C., 20402, Stock No. 004-000-00345-4.
WARNING
Th
is product equipped with a three-wire grounding (earthed) plug - a plug
that has a third (grounding) pin. Th is plug only fi ts a grounding-type power
outlet. If you are unable to insert the plug into an outlet, contact a licensed
electrician to replace the outlet with a properly grounded one. Do not defeat
the safety purpose of the grounding plug.
•
•
•
•
CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the AC
voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.
Plug Type North America
European
Continental
U.K. Chinese Japanese
Plug Shape
Country
Voltage
U.S.A./Canada U.K. China Japan EU (except U.K.)
120* 230 220 100 230
*When operating the PlasmaSync monitor with its AC 125-240V power supply, use a power supply cord that matches the power
supply voltage of the AC power outlet being used.