Numark Industries CDN90 - Manual (Page 18)

CDN90
PROGRAM FUNCTIONS PLEASE READ!!!!
This button provides several programmable functions depending upon the combination of buttons used.
Track Sequence Programming - Depress while the unit is stopped with a CD in the drawer and “
” will light. Select each track to be programmed then press between selections. Press
“PLAY/STUTTER” to start the track sequence program playing. To exit and erase program hold for more
than 2 seconds while the unit is stopped, open the disc tray, or turn off the power.
The following functions will work by pressing followed by appropriate function while still holding the
program button:
Effect Options - pressing program with an effect button will offer alternative options to that effect when available. In
the case of the “SCRATCH” effect the display will toggle between “ SCRATCH 1,2,3, & 4”. More information on these
options is available in the effects section of this manual. *
Multiple Effect Mode – this switches the unit between multiple and single effect modes. More information is available
in the effect section.*
End of track dead space elimination – this will give and option for eliminating the dead space at the end of tracks.
The unit already automatically removes dead space at the beginning of tracks. End of track dead space elimination is
useful if you are playing a CD continuously and want to eliminate all the gaps between songs. The display will indicate
“
” when the function is set to eliminate space and indicates “ “ when the unit is left to leave the
natural space between tracks. *
Cueing Style Selection – this will alternate the jog wheel cue function from a smooth “scratch” sound to the tradition
“stutter” sound modes during cue operations. The display will indicate “
” when the “scratch” style is
active. This indication will go away when the style of cue is stutter. During “Video” Digital out mode this will disable
autocue to prevent video clipping. For more info please see “Digital Output” below.*
Brake Speed – this allows you to adjust the speed of ‘PAUSE”, or braking. Press “PAUSE” then rotate the wheel until
the desired seconds of startup are shown. Pressing “PAUSE” twice will toggle startup from “
” to the desired
seconds. *
Startup Speed – this allows you to adjust the startup speed of initial play. Press “PLAY/STUTTER” then rotate the
wheel until the desired seconds of startup are shown. The “STUTTER” function will not be affected. Pressing
“PLAY/STUTTER” twice will toggle startup between “
” and the desired seconds. *
Relay time – this gives options for the amount of time used for relaying between tracks on two connected units.
Options will appear to relay immediately after the track (0), with time added of 1, 2, or 3 seconds (1,2,3), or a
reduction of 1,2, or 3 seconds (-1,-2,-3). By reducing time the attached CD player will start playing before the end of a
track, creating an automatic segue. This feature will also work in track sequence program mode; however, if the units
are also in SINGLE mode the same number of tracks programmed should be the same. Play will stop at the end of the
last track. *
Remote Start – The sets the mode for the “remote” jack on the rear of the unit. Details can be found in the relay and
remote start sections of this manual. *
Automatic door close protection – this option automatically closes the door at the specified time. The display will
indicate 30 seconds, 60 seconds, 120 seconds, and (no) for no auto close. *
Digital Output – This unit has full time digital output. This combination toggles the digital output to allow raw digital
information to be extracted from the CD for CDG video purposes. “VIDEO” will be indicated in the display in this mode.
When this mode is active the unit will not allow for seamless looping or other effects that would disrupt the video.
During this mode, PROG + CUE will also turn autocue on and off for video mode only. In case the DJ wants to disable
auto-cue so that the CDG doesn't skip over the video frame before the song comes in. When you wish to digitally
record your effects the unit should be put into “AUDIO” mode.*
Smart Looping – When active the display will indicate “ ” and all looping and stuttering will follow the beat
of the music based upon the Beatkeeper information.
Sleep Mode – The unit will automatically enter sleep mode after 15 minutes of inactivity. In this mode the unit will
still start instantly from buffer, however, the laser will turn off to extend it’s life. If this feature is undesirable, then it
can be turned off. *
*This setting will be remembered at power down.
- The Leader in DJ Technology
©2002 Numark Industries - 18 - http://www.numark.com