Onkyo DV-SP800 - Manual (Page 12)

12
Index to Parts and Controls
1 VIDEO OUTPUT COMPONENT jacks [16]
If your TV has component inputs, you can connect a component
video cable to your TV and to your DVD Player for ideal video
quality. The component Video Cable only carries the video signal;
remember to connect the left and right audio cables. If you connect
a TV that is compatible with a Progressive scan signal, you can
enjoy both Interlaced and Progressive scan.
2 VIDEO OUTPUT S VIDEO jack [16, 17]
If your TV or monitor has an S-video input, clear picture
reproduction is possible by connecting the player to your TV or
monitor via the S-Video jack.
You can switch between [S1] and [S2] S-video output from the
Setup menu.
3 VIDEO OUTPUT VIDEO jack [15]
Connect to the video input on a TV or monitor or AV amplifier or
receiver with video input capability.
4 AC INLET [20]
Use to connect the power cord to the wall outlet.
5 ANALOG OUTPUT CH 1/CH 2 jacks [16-19]
Use to output two-channel audio (analog) to the audio stereo
inputs on a TV or stereo amplifier.
6 ANALOG OUTPUT FRONT/SURR 1/CENTER/
SUBWOOFER jacks [19]
Use to output 5.1 channel audio (analog) to the 5.1 channel
discrete inputs on an amplifier. If you are connecting to a
receiver that has both digital and analog input jacks for DVD
player connection, it may be beneficial to make both connections.
7 SURR 2 jacks [19]
Use when making connections to 7.1 channel analog inputs.
(Make sure the SURR 1/1+2 selector switch is set to 1+2.)
8 SURR 1/1+2 selector switch [19]
When using 2 channel surround, select 1, when using 4 channel
surround, select 1+2. Audio will be output 3dB lower when 1+2 is
selected. The same audio is output from SURR 1 and from
SURR 2.
9 DIGITAL OUTPUT OPTICAL jack [18]
Use to output the digital audio signal recorded on discs. You can
output the digital signal via the optical output jack to an AV amplifier
or receiver.
0 DIGITAL OUTPUT COAXIAL jack [18]
Use to output the digital audio signal recorded on discs. You can
output the digital signal via the coaxial output jack to an AV
amplifier or receiver.
- z jack [18, 19]
Use to connect this player to another component bearing the z
mark. This lets you control this unit as though it were a component
in a system.
(The components will not function as a system with only z
connections. Be sure to connect the audio connection cables
correctly as well).
(European models)
= AV CONNECTOR 1 (IN/OUT) jack [17]
Use a 21-pin SCART cable to connect to a TV, monitor or video
component compatible with this type of connection. Outputs both
audio and video (composite only) when the unit is powered on.
When the unit is in standby mode, this jack becomes an input for
audio and video (RGB, S, and composite).
~ AV CONNECTOR 2 (OUT) jack [17]
Use a 21-pin SCART cable to connect to a TV or monitor
compatible with this type of connection. Outputs audio and video
(RGB, S, and composite) when the unit is powered on.
When the unit is in standby mode, this jack outputs the audio and
video input from the AV CONNECTOR 1 jack.
■ Rear panel
Shapes of jacks vary depending on the area in which it was
purchased.
European models.
OPTICAL COAXIAL
L
R
L
R
SURR
1 1+2
SUB
WOOFER
AC INLET
REMOTE
CONTROL
DIGITAL OUTPUT
S VIDEO VIDEO
Y PB PR
COMPONENT
CH 1 CH 2 FRONT SURR 1 CENTER SURR 2
VIDEO
OUTPUT
ANALOG
OUTPUT
MODEL NO. DV-SP 800
SACD & DVD AUDIO/VIDEO PLAYER
1 2 3
5 7 6 8 9 0 -
4
OPTICAL COAXIAL
L
R
SURR
1 1+2
SUB
WOOFER
AV CONNECTOR 2
REMOTE
CONTROL
DIGITAL OUTPUT
S VIDEO VIDEO
Y PB PR
COMPONENT
H 1 CH 2 FRONT SURR 1 CENTER SURR 2
MODEL NO. DV-SP 800
SACD & DVD AUDIO/VIDEO PLAY
AV CONNECTOR 1
OUT IN/ OUT
= ~