Quadra-Fire HUDBAY-INS 7008-115 User Manual
Page 2
Quadra-Fire • HUDBAY-INS • 7008-115 Rev. o • 8/11
2
Model Name: ___________________________________________ Date purchased/installed: __________________
Serial Number: __________________________________________ Location on fi replace: _____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________
A. Congratulations
Congratulations on selecting a Quadra-Fire gas fi replace,
an elegant and clean alternative to wood burning fi replaces.
The Quadra-Fire gas fireplace you have selected is
designed to provide the utmost in safety, reliability, and
effi ciency.
As the owner of a new fi replace, you’ll want to read and
carefully follow all of the instructions contained in this
Owner’s Manual. Pay special attention to all cautions and
warnings.
This Owner’s Manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.
The information contained in this Owner’s Manual, unless
noted otherwise, applies to all models and gas control
systems.
Your new Quadra-Fire gas fi replace will give you years of
durable use and trouble-free enjoyment. Welcome to the
Quadra-Fire family of fi replace products!
We recommend that you record the following pertinent
information about your fi replace.
Homeowner Reference Information
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
APPROVED FOR CANADA AND USA TO:
ANSI Z21.88b-2003 / CSA 2.33b-2003 Vented Gas Fireplace Heate r, and applicable sections of UL307b Gas Burning
Heating Appliances for Manufactured Homes and Recreational Vehicles, CAN/CG A 2.17-M91 “Gas Fired Appliances
for use at High Altitudes.”
This appliance is manufactured for operation with Natural Gas. For conversion to propane the Manufacturer’s kit
provided with the stove must be used in conjuntion with the instructions in the owner's manual.
This vented gas fireplace heater is not for use with air filters.
This appliance may be installed in a bedroom or bedsitting room; in Canada remote thermostat installation is
required.
FAN TYPE VENTED CIRCULATOR Blower Electrical Rating115 V., 1.5 Amps, 60 Hz, 150 Watts
For use with Natural Gas
For use with Propane
"0-2000’
"0-2000’
Input Rate on “HI” (BTU/Hr)
30,000
28,000
Input Rate on “LO” (BTU/Hr)
22,500
22,650
Main Burner Orifice (DMS)
36
52
Minimum Inlet Pressure (Inches W.C.)
4.5”
11”
Maximum Inlet Pressure (Inches W.C.)
7.0”
14”
Manifold Pressure on “HI” (Inches W.C.)
3.5”
10”
Efficiency up to 82.5%
81%
AFUE
71%
72.5%
2005
2006
2007
Feb
Mar
Apr
May
Jun
Jul
Aug
Sep
Oct
Nov
Dec
Jan
DO NOT REMOVE THIS LABE
L
MADE IN U.S.A.
Date of Manufacture / Date du Manufacturier
MINIMUM CLEARANCES TO COMBUSTIBLES
This appliance equipped for altitudes 0-2000’ (0-610m) in USA; and in Canada for altitudes of 0-4500’ (0-1370m). In USA for
Altitudes above 2000’, the vent configuration, orifice, or combination of both may need to be changed. See Owner’s Manual for
information on making these changes.
This appliance must be installed in accordance with local codes, if any (and Commonwealth of Massachusetts approved); if
none, follow The National Fuel Gas Code,ANSI Z223.1 and NFPA 54; or Canadian Installation Codes CAN/CGA-B149.
NOTE: Have the gas supply line installed in accordance with local building codes by a qualified installer approved and/or
licensed as required by the locality. (In the Commonwealth of Massachusetts, installation must be performed by a licensed
plumber or gas fitter.)
Manufactured by:
7031-221
P.4.1-02 Canada Minimum Pipe 69% NG / 71% LP
Report No. / Rapport Numero
061-S-63-5
MODEL: XXXXXXX
VENTED GAS APPLIANCE
NOT FOR USE WITH SOLID FUEL
SERIAL
NO.
XXX
Tested and
Listed by
Beaverton
Oregon USA
OMNI- Test Laboratories, Inc .
C
R
SAMPLE OF SERIAL NUMBER / SAFETY LABEL
LOCATION: HANGING ON A CHAIN ON BACK OF APPLIANCE
Manufactured
Date
Serial Number
Model Name
Test Lab &
Report No.